What are you building with your milled wood?

[Johnmn]

Here was 4 of 6 finished cutting boards, last week stuff.

 

[Guido Salvage]

I had a friend ask me about making a drying rack for reusable water bottles so I whipped this up for her.

 

[Wolverine]

View attachment 312499 View attachment 312500 View attachment 312501 View attachment 312502View attachment 312507

Can you show the joinery for this piece? Very nice!

 

[RI Chevy]

I am interested too...

 

[merc_man]

Mee three

Sent from my SM-G950W using Tapatalk

 

[PA Dan]

Four...

 

[birdmeter]

Can you show the joinery for this piece? Very nice!

art right here.

 

[Wolverine]

art right here.

Definitely a nice piece! I have literally tons of milled wood around and this could be a nice project to use some of it on. I'm guessing maybe pocket holes.

 

[Benwa]

Can you show the joinery for this piece? Very nice!

Thank you. Yes, I used a Kreg/pocket hole jig. I routered "channels/pockets" in the rear of the backrest to fit over the uprights as well as the bottom of the seat to fit down over the "legs." Hope that makes sense. The angle of the backrest took a bit of playing around with to get it comfortable. I don't have the bench, as it was a gift for someone. I'll see if I can't get over to their place this weekend (it's close by) and get some pictures, measurements, & angles for ya to go off of.

 

[RI Chevy]

Cool. Thank you!

 

[Wolverine]

Thank you. Yes, I used a Kreg/pocket hole jig. I routered "channels/pockets" in the rear of the backrest to fit over the uprights as well as the bottom of the seat to fit down over the "legs." Hope that makes sense. The angle of the backrest took a bit of playing around with to get it comfortable. I don't have the bench, as it was a gift for someone. I'll see if I can't get over to their place this weekend (it's close by) and get some pictures, measurements, & angles for ya to go off of.

Yep, makes sense and is what I thought. Thanks for the follow up and future info.

 

[MustangMike]

Made another shelf for my Upstate Cabin, 2" thick Red Oak stained with my home made Walnut stain (it is only good for inside stuff).

My wood has been stored outdoors for too long and it starting to get some bad spots.

 

[RI Chevy]

Nice Mike.

 

[MustangMike]

This bench will go up to the cabin, near our outdoor fire place. We will sit on it in both directions.

It is Red Oak, 3" thick, 7.5' long, finished with Teak Oil.

 

[Firewood Hoarder]

Turned out there is some nice grain hiding in this Ash crotch I saved... probably going to try my hand at making an end table or two if I can get the slabs to dry without a ton of cracking...

 

[MustangMike]

My glass doors have not arrived yet, but I put the new gun cabinet (plywood and milled Red Oak) in the basement and it now holds my shotguns and lever action guns.

Left to Right,

1) Lefever 20 ga Trap gun. Single Shot
2) Ithaca 37 Deer Slayer Pump
3) Savage/Stevens 12 Ga Semi Auto
4) Rem 870 12 Ga Pump
5) Model 71 Winchester 348
6) Browning Repro of a Mdl 95 Win - 30-06
7) Mdl 94 Win Buffalo Bill Comm 30-30 w/26" Octagon bbl

 

[merc_man]

Gonna make.some boards for the new trailer. Should almost have enough after the last three boards i can get from the log. But thats it for today. Dam work gets in the way of all the fun

Sent from my SM-G950W using Tapatalk

 

[Guido Salvage]

A butcher block table for my daughter. It will measure 26.5” x 44” when I am done and will match the rolling cart I made several years ago.

 

[RI Chevy]

Nice work Guido

 

[merc_man]

Boards are all ready and i am pooped lol.
Now to get ready for work

Sent from my SM-G950W using Tapatalk