husqvarna

Hi Guys - I'm letting loose of a few saws I don't have time or room for - First up is a Husky 372 OE that I rebuilt a couple years ago. I split the case and installed new Nachi bearings and OEM seals + gaskets. I used a new OEM top end (71cc) that I got from a member here who is a dealer (it...

Hi! I'm experiencing a lot of issues with my T540XP mark II chainsaw when attempting to start it. I can sometimes get it to ignite, but it never idles. It's possible to start when giving full gas at the same time, but it dies when the throttle is released. When attempting to start it, I...

Hey there Guys and Gals, Looking for a couple of parts for a 262xp project for myself. Can pay or possibly trade if I have something you need. Fist is an air foil that goes between the starter and the flywheel. Next is a clutch cover complete with functioning chain-brake. Let me know what you...

Hey guys, Any ideas on what this wood is? I'm in the South Island of New Zealand. Was pretty sure it was macrocarpa but my neighbor thinks it might be gum. Has been down for about 5 years. Using my Husqvarna 450 to slice it up!

So I just picked up two brand new Husqvarna 439's on ebay, made the guy an offer I never thought he would take... I've never actually seen one of these saws or heard anything about them so I'm coming here for knowledge. Anyone got any info or any opinions of this saw? If anyone's been looking...

Hello fellas! Firstly For all of the conversations I read in the past weeks helped me rebuild my first chainsaw, but ...! it’s a small but, ie: after rebuild which is : -top cover opening for better cooling -muffler drilling for slightly better exhaust flow -spark plug gaping -side transfer...

Hello, I have 10+ k750/760 carcasses, i think the only think i dont have any of is right side cases(cracked) and good pistons, i May even have 1 or two fully good cases. Let me know what you are looking for and i will send a pic and price. Thanks, Justin

Hey guys - I'm putting my recently rebuilt 346XP up for trade. It's an OE that thinks it's an NE. I went through this for a member here for a potential trade deal and then we decided to go a different direction. The member wanted all new components inside, so I split the case and installed new...

Lookning for a 576xp crankshaft assembly part # 505 12 19-02. Also interested in a 576 that with a burnt up cylinder. Thanks.

Just picked up a new 372OE that has a blue coil stamped 2018 PN 586 88 03-04. Is this coil limited? I can't seem to find any info on it except a listing on Ebay that says it is 372 specific. Thanks.

Pulled down my low hour 2071 and found this. Does the later model 372 crank swap in or do I need to change the PTO side case half as well?

Hey All, I have a Husqvarna Petrol Blower (Model 125B) and just this week I have been feeling it wobble/shake/vibrate more than usual, at full throttle, and I have noticed the Air Filter box and Choke mount is very easily moved by hand, its easier to show you what I mean, so I have uploaded a...

FS Jonsered 2253 with the MMWS treatment. The saw has less than 1 hr of runtime according to the dealer who updated the carb software in Sping 2019.if you’re not aware of this model it’s identical to the 550xp MK1 but just in red. $750 Shipped Paypal F&F to your door if you live in EST, CST, or...

FS a very good condition 2001 model Husqvarna 395xp PHO with mild port work and muffler mod. All OEM except muffler, Meteor piston, and Caber rings. OEM full wrap with West Coast kit and front case protector. $750 Shipped PayPal F&F to those in EST, CST, MST. If in PST or outside the...

I am yust looking for an Ignition Coil with Bosch-Nr. 2 207 031 145 Shipping to Germany What's Your price

Hi guys, I saw yesterday on FB that Patrick Lacey had an unfortunate run in with a dirty rotten snag on the job and is currently laid up. From the sound of it it was pretty bad. He is not looking for donations so I figured I would take a cue from his buddy that posted on FB and try to get as...

Are these sought after? What is the deal with them being painted orange? Any info is appreciated.

Curious as to what piston replacment everyone is using on the later 357xp. (15mm needle bearing) Oem jug, modestly ported. Oem pistons are looking pricey. I'm seeing pop ups made by hyway and lilredbarn but I'm a skeptic.. I also read to steer clear of the hyway flattop replacment piston...

Sold pending local buyer. 11 saws total. Most parts are there.

Hey guys- I'm looking for a good condition 385/390 flywheel side case half. I have cash or lots to trade for it. Thanks!