husqvarna

I have a 288xp I would like to use for milling. My current dilemma is rather I should just use 36" bar with it, which won't max out my 36" Alaskan. Or if the saw would be able to run a 42" bar which would allow me to use the full 36" of mill. I am worried I will be asking too much of the saw.. I...

I have a anniversary edition 288xp I picked up, runs great, no issues, until it gets low on gas. I say this because when it gets down to less than 1/4 tank, the idle picks up speed, like its leaning out. The fuel filter/weight is free to move around, I've checked. Any ideas? Thanks, Dan

I have a 1989 288xp with a metal brake flag. Turns out these brake bands are prone to breaking and hard to come by. Anyone know where I can find a replacement? Doesn't seem to be a oem option anymore, aftermarket is fine if it's high quality. Thanks I am new to the page, and tried search...

2000 model year 372xp. I went through this saw top to bottom. 100% OEM saw. New rings while I had apart. Bearings are good. Full wrap and big dogs. New air filter, spark plug, top filter cover, bar studs, rim sprocket . Muffler modded the original exit hole. Blended lower transfer while jug was...

Am I missing something or do you have to elongate the stud slot on a D025 mount to be able to mount a chain when running them on Hooskies?

I have a Husqvarna 140 x-torq which I'm currently repairing. Initially the saw would not start so I cleaned the carb and it now starts and idles perfectly. The problem is that it will not rev up fully. The carb on this saw looks a little different to what I seen before. It has two bores, one...

Husqvarna 545 fully rebuilt from the crank up with all NEW OEM parts. Cylinder, piston, ring, bearings, seals, case gaskets, lines, filters, clutch drum, oil worm gear, .325/7T sprocket, spark plug, etc. Pressure and vac tested 100% using OEM Husqvarna block-off plates. I have video of it...

Husqvarna 545/550xp cylinder in excellent condition no transfer, scoring, or other damage. It still has the cross hatching in the cylinder from the factory. P/N 577 76 47-06 Also fits Jonsered CS2252/2253 $60 Shipped

Updated: 2014 Husqvarna 372XP XT. Starts and runs missing choke lever. Missing a few screws (1x on top cover & 1x on muffler bracket). Compression is ~140psi cold, the piston is worn, but isn't scored. This saw will make someone a great work saw or backup saw with a bit of minor maintenance. New...

Husqvarna 359 all OEM. Now has the upgraded metal intake clamp and gasket delete with a factory muffler modified to dual port. Clean and nice oils and runs great. $275 shipped to ConUS not including anyone in PST (PM for detailed shipping quote). If you have any questions just let me know!

Husqvarna 372XP OE converted to XPW (75cc) using brand new OEM Mahle P/C. Gasket delete and front ported muffler with full wrap bars and west coast spikes SEM unlimited (black) coil. $575 shipped in the ConUS unless in PST (contact me directly for exact shipping quote. PM if you have any...

Selling a Jonsered/Husqvarna bar and chain combo package $100 shipped in the ConUS unless in you live in PST, please just ask for a shipping quote. 1x 24" Jonsered branded bar with almost no use "B" mount 84 DL 3/8" pitch .058" 1x Jonsered branded chain NIB 2x Windsor branded chains NIB 4x...

Can someone tell me the bore and stroke of the Husqvarna 450 rancher that is advertised as 50.2cc? Thanks. And also if there is a big bore cylinder and piston kit for it, and what cc that would then make the engine.

Hey, everyone in a previous thread you may know that I am married and live alone so I figured I would share what I come home to.lol this is an anything thread feel free to go nuts.

Have a nice running 272xp professional chainsaw. Will be a great firewood saw. $380.00 with 18"bar and chain pictured and in vidja, or $350.00 PHO, both prices are shipped to the lower 48 states. Paypal F&F. List of parts replaced: OEM: wrist pin bearing curly fuel line both seals and O-Ring on...

Hey guys- I rebuilt two pretty nice saws - one later poly flywheel bubble-top Stihl 066 and one later Husqvarna 288. The 066 I built for an arborist buddy who ended up taking my 385. The short block I got from a member here- it was in good shape but had been hit by a tree and the tank and all...

Selling this nice Husqvarna 570 Professional chainsaw. Was a rebuild from two donor saws, one an extremely low hour crush victim with a beautiful P&C and one with a burned top end. This combined with some new OEM parts including a top cover handle and soft grip, along with air filter, line and...

Hi Boys- I'm looking for a set of Husky 181/281/288 crankcase halves for a cant saw build. Rough is ok, as I might send them in to be coated. I have cash or trade. Thanks!

I joined OPE a couple weeks ago after seeing Chainsaw Jim's 357XP Hybrid Build, & thought WOW I need to follow up on this Build. It stared last Fall when I'd Purchased a J-red 2159 with a new OEM Top for my midsize saw. When I got it back to the shop to investigate it further I'd realized the...

Looking for a 75cc+ saw or saws willing to trade a yz250f 2007. Have pictures of the bike if your interested. Pm me and we can talk more about the deal.