husqvarna

Curious as to what piston replacment everyone is using on the later 357xp. (15mm needle bearing) Oem jug, modestly ported. Oem pistons are looking pricey. I'm seeing pop ups made by hyway and lilredbarn but I'm a skeptic.. I also read to steer clear of the hyway flattop replacment piston...

Sold pending local buyer. 11 saws total. Most parts are there.

Hey guys- I'm looking for a good condition 385/390 flywheel side case half. I have cash or lots to trade for it. Thanks!

Hi Guys- I'm looking for another 288 High-top cover if anyone has one they can spare. I have lots to trade and cash - I'm currently loaded up on big saw stuff - 3120, 084, 394/395, 046/460, 372, 2100.

Whats the nearest pro saw to the 346 Husqvarna currently make, was the Jonsered 2153 it's red cousin. I never had a 346, and see references to the 346 being 46cc others say 50cc, confusing. Would the Stihl 241 have the same capability as the 346.

Hi to all Just wondering if anyone has a parts list for the new Husqvara 545 MK2, or more to the point, does this new saw use a Two ring piston, or did they keep the One ring affair of the older model. They say its an all new design, and my search so far has revealed nothing about the innards...

Faced with the problem of a missing pawl on a SEM flywheel. Only the spring and pawl being still available as replacement parts. The stud is nla. Figured I would see what else could be found to make it work again. Dug through my bolt bin and found what I believe is a stud from a 2 series of saw...

Hey Guys- I need a good 395 flywheel and a couple of 20" Husky large mount bars in .050" x 3/8ths. I have cash or trade. Thanks!

Hey guys - I went through and rebuilt another pretty nice 288. I got part of this project from a member here, and part of it from a local trade. This one has a new OEM piston and ring in a very nice Gen 1 Mahle cylinder (A/B piston in an "A" cylinder). It got all the other usual goodies - new...

I bought a bunch of parts to fix a few chainsaws. I just opened this: Husqvarna 390 XP 385 Jonsered 55MM Cylinder Piston 2188 2186 544 00 65 02 Item NO: QG38555 https://www.huztl.net/h-product-detail.html?goods_id=402847 The piston pin bore is oval on one side and instead of it being 13MM...

Hi, I need a service manual or workshop manual for Husqvarna 553RBX brushcutter. Anyone knows where I could get one?

looking for a flywheel for a 395xp! Whatcha got?

Hi Guys- This is a long shot but I'm after a high-top cover for 288. A local Arborist buddy wants me to build him a high-top saw for falling. I have cash or tons to trade. Thanks!

Hi all, looking for information on the 550xp pto side bearing. I know there has been an update (or 2?) since the 550 and 562 has been released. I am looking at bearings and see both the 525 43 42-01 and the 525 43 42-03 bearings listed for the clutch side. Which one is the one I want? They are...

So I am rebuilding a 2171 from a busted up saw I got relatively cheap from ebay, the plan is to put the 75cc top end on it and then I plan to have it ported afterwards. I dont have a whole lot of experience gauging wear on a crank, so I was thinking I might just buy one that is good from...

Hey guys- I'm putting up what will probably be my last high-top 394 ever. I got most of the carcass for this from a long-time member and slowly accumulated the remaining parts I needed for the build. I split the case on this a couple years ago and went through the bottom end with new Nachi...

272xp @Termitebuffet Split the cases & built with the following: • New meteor piston • New OEM bearings, seals, gaskets, carb kit. • Chain brake works. • Cut to set squish for no gasket: compression bump. Saw is in Asheboro, NC @ Zoo City Saws. It Possibly can be at the Mastermind GTG...

Can anyone ID the two cylinders in the front row of this picture. I can't get sizes or any more pictures from the seller unfortunately. I was guessing 2 series Husky, maybe 281 or 288 hopefully.

FS: Extremely low hour 1997 Jonsered 2065. All OEM no modifications. Has a standard 7pin PowerMate sprocket, pre-1998 EPA Zama C3M-2B carb, single felling spike, OEM muffler in perfect condition. This is a large mount saw and has the front chain tensioner which can easily be swapped to a side...

First off thanks for having me been lurking and finally registered! I like to piddle around with just about everything and anything! Hence I created a YouTube channel where I share my projects and ideas! Follow the link to the latest episode! This episode of American Piddler I discuss how...