Came across this Meteor 50mm 372 cylinder kit on ebay. Seems like a low price and the color looks darker than the other Meteor kits I have seen, only pictures as I have not handled one myself. Wondering if anyone can shed some light on this...
Picked up this Hyway 45mm cylinder with a meteor piston for a swap on a Jonsered 2152. I have little experience with cylinders and saws in general to be honest, am wondering about a couple things. There is a band of checkered material at the top of the bore from the squish band to about half way...
http://blog.hlsproparts.com/2016/09/complete-guide-to-husqvarna-550xp.html
At the link above you will find the Husqvarna-550XP parts list with exploded parts diagrams.
I hope it saves you some time.
Good condition Husky 335xpt top handle. Bought locally, used the saw a few times until I found a 200t. Runs good, comes with a 12" bar and total of 4 chains. Bar oils well and gain brake works. Always ran at 40:1 with Stihl oil. $200 plus shipping from 49345. I can pm more pictures and a video...
Ok guys- I got two freshly rebuilt saws for sale or trade. Both were completely gone through by myself, a proud graduate of Stihl Icademy and the Haitian Institute of Beauty and Technical Massage Therapy.
The 390XP:
This one resulted from a lot of trading with members here. This one ended up...
Hey Guys-
I'm looking for a 562 or a (preferably) 555 carcass. It can be in various stages of disrepair or a running saw. I have cash or other saws to trade, including a freshly rebuilt 390XP. Thanks!
Hey guys-
I'm looking for a wrap handle for a Jonsered 2094 (I can make 2095 work also) project and a set of crankcase halves plus a tank for a smashed 555. I've got tons to trade and cash. If you're in need of Husqvarna, Jonsered, Stihl, or McCulloch stuff- let me know as I probably have it...
This Tillitson HS would not pass a pressure test at all after rebuilding with a Genuine RK-23-HS kit. After checking the usual suspect, the needle valve, it was obvious something else was amiss. Dunked it in a jar of water and bubbles were pouring out the impulse port. Took the cap off the fuel...
Hi Guys-
I'm chasing a nice clutch side (PTO) crankcase half for 394/395 or a whole crankcase. I bought one off ebay but it turned out to have a wallowed out bearing pocket on the PTO side, which happens a lot when people run long bars and keep their chain too tight. I have cash or lots to...
Hello Folks
Firstly, Nice to meet you all and apologies for being the new guy who comes crashing in on your forum with a tech question.
So, picture the scene, you're a power tool repair guy by day and saw collecter by night. One of your friends see's you working on a saw one day and asks if...
Got this Husky 141 for $30. Super clean with, of course fuel lines crumbled inside of the tank. Owner either barely used it or take extremely good care of it. I've research and found that modding the muffler will turn this little saw up a notch(not much). I can't find pictures nor a step by...
I have the opportunity to get a husky 141 in pretty good shape. I've done some searches and some say it has a great power/weight ratio, while others kick it down because it is an orange Poulan saw. I'm here to learn, so any input is appreciated. Thanks Craig
Is there a way to tell by looking at the saw if the bottom end of the 562 was replaced? The seller says it was done by Husqvarna. I have seen them rebuilt, the color of the crank case gasket was green, but if it was a full factory replacement I would assume they would be black or grey. Any...
Back story... bought my tree five seven new 2010. Cut 7-10 cord per season and ever since new I always felt the oiler was stingy. With it turned up to the max and the bar oil holes slightly enlarged I always used about 1/2 tank of oil per tank of gas. Well after a little research and some help...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.