What's on your bench?

[Stump Shot]

My first professional porting job, ground out the oiler ports on an Oregon bar. LOL Changed an oil pump in a Jonsered, and installed a new fuel line and filter on a Husqvarna 353. They were both gone as fast as I could do 'em, off to cut wood.

 

[Czed]

If everyone else is like me. I start cutting next years firewood in early October. It seems like everybody waited all year to bring me their broken saws since sat i have two husky 288s a 340 three stihls 025 028 290 and a fs 90 at least it's cool enough to work in the shop finally.

 

[Definitive Dave]

adjusting carbs is hard

 

[dall]

i have guys i work with ask me alot to work on thier stuff so i work on them after i get home tomorrow im picking up 2 to work on

 

[TJ the Chainsaw Mechanic]

024 I've been fighting for to long.

 

[beaglebriar]

ATV engine almost finished. Just have to put the clutch back together.

Time to get some sleep...

 

[Jughead]

today actually got a chance to almost finish my red lever 026.still need a fuel line and a tank vent.gasket delete wound up to be .014 so i found a Husqvarna pump sprayer warranty card in my floor board that had a .005 thickness and cut a gasket.torqued down gave me .018.
Flywheel key filed down .030.muffler mod just as soon as i get the muffler derusted. or i could just modify one of daves mufflers.

 

[VinceGU05]

A Honda GX160 coupled to a 2" Aussie firefighter pump is currently on my bench....it's a non runner........& hasn't been 4 quite a while I'd say.
View attachment 35649
Just a little sediment in the bowls lol

lol.. water in the fuel is it?
my dads fuel tank looked like that.. carby was pretty clean tho. still wouldnt run. tiniest bit of dirt must of plug it up.. oh also the air filter was oil soaked ( tipped on its side i think at one stage) maybe it couldnt breathe thru it.

 

[Brewz]

I always wanted to do twins.
These twins were free from the rubbish dump and are very dirty but should clean up ok

 

[Stihl working Hard]

ATV engine almost finished. Just have to put the clutch back together.

Time to get some sleep...

Looking good what size is the motor

 

[Brewz]

And done

 

[Brewz]

Anyone know if there is an after market crank available for a Stihl 021?

Id like to know where the cage went. It was all together untill I pulled the main bearings from the cylinder. Was no cage in sight and no marks or damage where it may have passed through the motor.

Very odd

 

[VinceGU05]

might be like the 009 010 011 012. they run without a cage too. grease and tweezers to get it back together.
yup.. just checked on medicat. same same. all good .

 

[Brewz]

might be like the 009 010 011 012. they run without a cage too. grease and tweezers to get it back together.
yup.. just checked on medicat. same same. all good .

Well there is a new challenge.
what a PITA!
I was about to download the IPL. Thanks for the info mate, much appreciated!

 

[Postrip]

lol.. water in the fuel is it?
my dads fuel tank looked like that.. carby was pretty clean tho. still wouldnt run. tiniest bit of dirt must of plug it up.. oh also the air filter was oil soaked ( tipped on its side i think at one stage) maybe it couldnt breathe thru it.

Yeah a lot of water Vince!, been sitting a long while also.
Wet or oil soaked paper air filters certainly choke things up

 

[Brewz]

Water is the enemy

 

[Stihl working Hard]

Water is the enemy

View attachment 36091

Wow that's pretty knackered isnt it

 

[exSW]

Ugly. Took it out for one last test drive before boxing it up and sending it off and the idle was wonky. Block off the intake and exhaust,vac test and airleak. Waiting for the dealership to open so I can order/pickup new seals.

 

[bennne]

Anyone know if there is an after market crank available for a Stihl 021?

Id like to know where the cage went. It was all together untill I pulled the main bearings from the cylinder. Was no cage in sight and no marks or damage where it may have passed through the motor.

Very odd

View attachment 36079

View attachment 36085

You can use the same service cool that is use on the 1120 series on these. It holds the bearings in place and the rod steady. I just had an enquiry on a 010 with the same setup today

 

[beaglebriar]

Looking good what size is the motor

500cc