Testing Torque with 661s yesterday

[ferris]

I always run max oiler for my tests. 20" bar or 41". don't matter.

pin pushed in - that is the first thing I do when I get a new 661.

Can you explain that, i don't know about that pin?

 

[mdavlee]

Can you explain that, i don't know about that pin?

There's a pin on the oiler. Push it in allows for more adjustment for higher oil output.

 

[ctylerc1995]

I'm looking for some torque for my 661View attachment 10321 View attachment 10320

What lathe do you have there? WWII era? Nice setup!

 

[ferris]

There's a pin on the oiler. Push it in allows for more adjustment for higher oil output.

Can someone make a picture of the pin?
If i will push the pin, must i crew off something?

 

[mdavlee]

Can someone make a picture of the pin?
If i will push the pin, must i crew off something?

Someone that has one can probably do that for you. I don't have access to mediacat on my iPad or I'd get a picture from it.

 

[sawmikaze]

Can someone make a picture of the pin?
If i will push the pin, must i crew off something?

Just take a look with a flashlight by your oil adjustment screw , its basically self explanatory..nothin to it.

 

[Moparmyway]

What lathe do you have there? WWII era? Nice setup!

 

[Stihl working Hard]

was having some fun testing torque yesterday on 661s.

41" cannon - .404 RS full comp. wood - oak


stock 57.1 sec

snellerized - 43.2 sec

tree monkey - 28.9 sec ...who needs an 880 anyway?

Great videos there Redbull treemonkeys saw Wow

 

[Stihl working Hard]

I always run max oiler for my tests. 20" bar or 41". don't matter.

pin pushed in - that is the first thing I do when I get a new 661.

The pin on the oiler shouldn't be an option to knock it in it should just be able to turn on or off

 

[Nitehawk55]

What oil and mix ratio did you use ?

 

[TJ the Chainsaw Mechanic]

That's some nice goo there.

 

[Redbull661]

That's some nice goo there.

schaeffers 32:1 91 eth free

seems to work pretty good so far...after 7 or so tanks.

 

[Nitroman]

Those videos forever lay to rest the question: "is a ported saw better than a non-ported saw"?

I was on Faceplant where a guy was showing a freshly installed, ported 394 jug he bought off eBay. Just porting, no squish mods. He was very excited to say the least, then some Fud started commenting to the effect the porting was a fad, it didn't do anything, reliability went down...blah, blah, blah. I am going to see if I can message the guy and have him see these flicks.

 

[Rains]

Porting really wakes a saw up, it's been more than proven. I give it crap at times but the proof is in the pudding.

 

[Moparmyway]

I hope that I added some torque. I want to change something with the transferrs, but will run it like this while I save up for a new CC Specialties right angle handpiece

 

[Moparmyway]

Also

 

[Keith Gandy]

Also
View attachment 15427View attachment 15428

Am I seeing right that these 661s have an intake floor from factory @ 86°?

 

[Moparmyway]

Thats what I started with this go around, I have been tinkering with her for some time ................ those are not the factory numbers from that jug

 

[Keith Gandy]

Thats what I started with this go around, I have been tinkering with her for some time ................ those are not the factory numbers from that jug

Wow !! And u r to 93 now? Ive ran these but never been in one. Why so much duration?

 

[Moparmyway]

Cutting .050 off the base physically lowers everything, so the intake got dropped ............ never fear !!!
JB Weld is here !