036 build/port

[jmssaws]

What do you use to heat up the case? Heat gun? Propane torch?

Heat gun taking apart
Toaster oven putting together

 

[jmssaws]

You look like a baby duck commander. Couldn't take the beard?

Saw looks strong man. Kuddos

I was trimming and got carried away
Stupid thing will just grow back

 

[jmssaws]

036 was almost 15k and still a touch fat
I'm gonna run it some more in a little bit and try to get it freed up and broke in.

I was running it before the video with the screen in the muffler but removed it to see if it gained,it's noticeably stronger with the screen in.

It doesn't have a screen in the video but will have the next one

 

[cgraham1]

036 was almost 15k and still a touch fat
I'm gonna run it some more in a little bit and try to get it freed up and broke in.

I was running it before the video with the screen in the muffler but removed it to see if it gained,it's noticeably stronger with the screen in.

It doesn't have a screen in the video but will have the next one

Good, because I really need to run a spark screen where I cut wood.

 

[jmssaws]

Good, because I really need to run a spark screen where I cut wood.

All removing it did was make it louder and slower

 

[junkman]

If i remember right the 034 exhaust flange was a little further back than my 036 was ,did the 034 muffler get used ? or a spacer needed ?I liked the 034 super i used to have ,it was my only saw for years ,the factory opening was a big rectangle in the front cover .

 

[cgraham1]

If i remember right the 034 exhaust flange was a little further back than my 036 was ,did the 034 muffler get used ? or a spacer needed ?I liked the 034 super i used to have ,it was my only saw for years ,the factory opening was a big rectangle in the front cover .

The saw is an 036. But it's an 034 super jug

 

[jmssaws]

I had to make a spacer.

 

[jmssaws]

I really like how it runs,cuts wood like a much bigger saw.
It's not far away from the 9pin 7900 in that situation.

 

[junkman]

Think it will need the clutch upgrade ,drum and bearing like the 044 has in size for the extra power ?

 

[jmssaws]

I don't think so but maybe.
I would switch the drum so I could use the big spline sprocket

 

[junkman]

I don't think so but maybe.
I would switch the drum so I could use the big spline sprocket

With a 28 inch bar on my old 034 and 036 pro the needles would fall out of the smaller bearing once in a while ,after the big bearing and drum upgrade it held up fine .

 

[jmssaws]

28" on a 034. Lol
I keep forgetting you guys cut paper mache'

 

[5000+]

036 was almost 15k and still

I was running it before the video with the screen in the muffler but removed it to see if it gained,it's noticeably stronger with the screen in.

It doesn't have a screen in the video but will have the next one

How big is the outlet? I've put the screen back on one or two that had been opened too much.

 

[junkman]

28" on a 034. Lol
I keep forgetting you guys cut paper mache'

With skip chain that 28 bar is like running a 21 inch bar with full comp right ?

 

[cgraham1]

With skip chain that 28 bar is like running a 21 inch bar with full comp right ?

1/3 less cutters, I believe.

 

[Backtroller]

I'm running the big bearing upgrade on my @drf255 036 Never had a problem

 

[RI Chevy]

Both saws sound great Jason. It reminds me of cutting like an 044 and it looks the size of an 026. Great saw there!

 

[jmssaws]

How big is the outlet? I've put the screen back on one or two that had been opened too much.

Not very big.

 

[jmssaws]

Here's some pine for you north west guys. 036 is at 15.2 and needs a 8pin
064 has a 9pin but didn't check rpm.
Around 14k I guess