What's on your bench?

[farminkarman]

Looks good!

Thank you sir! I am getting the hang of doing this….still takes me forever to get the jug zeroed before cutting though.

 

[PA Dan]

Thank you sir! I am getting the hang of doing this….still takes me forever to get the jug zeroed before cutting though.

Thats the toughest and most important part I'm sure! I warch it a bunch but I don't cut any myself.

 

[huskihl]

Thank you sir! I am getting the hang of doing this….still takes me forever to get the jug zeroed before cutting though.

My best time was 18 minutes for both the base and squish band cuts. And the next one took me 30 minutes for just the squish cut. For the most part it gets quicker the more you do, but every now and then one has to be a bastage

 

[farminkarman]

Getting a 346 jug dialed in to cut squish.

 

[Stevetheboatguy]

Parts washer sprung a leak....... Spread a lil fusor on the seam. Should seal it up until I can properly drain clean and weld it......... In a few years



Steven

 

[Stevetheboatguy]

Every one of these 575-576's needs a low top. The high tops just freggn get in the way. Added bonus is they look better. Way better. I'd prob swap the covers just for that.



Edit: Occasionally this saw gets loaned out. So I wont be drilling the adjustment holes. But if you wanted to, they are marked on the back side.


Steven

 

[WillG]

Serviced a Husqvarna K770 cut off saw. New fuel filter, air filter and pre filter, new plug and decomp valve, old one was sticking. Cleaned air filter base and around cylinder while I had the covers off.

Checked out a no start K770 and found that it died from dirt ingestion. Waiting for owner to get back to me to see what he wants to do with it.

Sent from my E6910 using Tapatalk

 

[mark_kershner]

Harbor freight anti fatigue mat is on my bench.

9$. Best upgrade I’ve done in years.


Sent from my iPhone using Tapatalk

 

[farminkarman]

Got a chance to circle back around to that 346 jug and cut the squish. Took 0.050” out of the band and cut a chamfer into the chamber. Also cut the cylinder extensions while I was at it. Now I just need the saw to show to keep moving.

 

[Ronie]

371k that's going to be converted to a saw.

 

[farminkarman]

Had a customer drop this thing off today. Apparently they can’t get it to start…should be interesting

 

[PA Dan]

MS460 getting a rebuild.

 

[Woodslasher]

I finished up this little gal who came to me with hard starting issues and some slight damage from being tossed out of a tree when it wouldn't start. The hard starting was due to a crankcase leak, so after cleaning the whole thing in the solvent tank I re-sealed the case and now it'll pass a p/v test with flying colors! After a bit of tuning it fires right up and I'm hoping it'll do the same when I return it to its owner. While I was at it I tuned my 056, adjusted the metering lever in it so it'll stop flooding itself out, and I also adjusted the valves on a Rammax trench compactor which should fix the hard starting/excessive smoking issues.

 

[huskihl]

MS460 getting a rebuild.

Seems awfully clean. What was up with the bearings?

 

[PA Dan]

Seems awfully clean. What was up with the bearings?

Ultrasonics do that to dirty saws. Buddy said he wanted his saw rebuilt. Old bearings were probably good for another 100k miles.

 

[sawnami]

Sorting out 5-XL400's

Sent from my LE2117 using Tapatalk

 

[qurotro]

What's the difference between those and XL12?

 

[Stevetheboatguy]

Yep...... They break it.... I fix it..... Every damn day. I like saws, them are more gooder......

But this pays the bills.




Steven

 

[Johnmn]

Yep...... They break it.... I fix it..... Every damn day. I like saws, them are more gooder......

But this pays the bills.

View attachment 330794 View attachment 330795 View attachment 330798 View attachment 330796 View attachment 330797


Steven

Nice looking repair!

 

[PA Dan]

Yep...... They break it.... I fix it..... Every damn day. I like saws, them are more gooder......

But this pays the bills.

View attachment 330794 View attachment 330795 View attachment 330798 View attachment 330796 View attachment 330797


Steven

Nice work brother!