What's on your bench?

[farminkarman]

Now that I have the base cut, I need to unshroud the lowers, and raise the uppers.

 

[Ronie]

Clutch cover I won in the raffle after some fresh paint, it should look good on my 440.

 

[Stevetheboatguy]

For the guys that don't visit the grease monkey thread.

Next I'm bringing back mullets




Just a test run to see if it works on the truck before the real bodywork happens. Didn't turn out bad for being a ten year old pint of paint. Total out of pocket was $0

Steven

 

[PA Dan]

For the guys that don't visit the grease monkey thread.

Next I'm bringing back mullets


View attachment 327782 View attachment 327783 View attachment 327784 View attachment 327785 View attachment 327786

Just a test run to see if it works on the truck before the real bodywork happens. Didn't turn out bad for being a ten year old pint of paint. Total out of pocket was $0

Steven

What panel will that match on the truck?

 

[Stevetheboatguy]

What panel will that match on the truck?

Different truck

The ugly mfr is my favorite though. I drive that one the most.

Steven

 

[Duce]

Finally finished this 394, new case half, bearings, gaskets, seals, brake handle, Meteor piston, Caber rings, trigger lock, fuel line, filter, etc. Just my typical rebuild. If you order this carb rebuild kit, ask if it has a diaphragm in it. One I purchased did not, found that strange to be a rebuild kit. Just added a week to rebuild .

 

[drf256]

Putting finishing touches on an 064. Cant wait to try and start this sucker. .030 off key, 200 psi compression and no sissy button.

 

[Maintenance Chief]

No elasto start ,no button? Your a braver man than I.

 

[drf256]

Elasto is a finishing touch. Gotta find it. Probably gonna dial advance back .010.

 

[RI Chevy]

Hold on, I'll be right over...

 

[bigbadbob]

We had a flood in Nov. Still finding damage.
My Lincoln sp175 got wet,, I didnt think it did.
Finally had time to try it. Well it turned on, had a arc.
But no wire feed. Removed liner,, fubar,, and still no feed.
Removed the drive unit and disassembled it, lil water in gear case, no damage.
12v dc motor had got a lil water inside, that left a lil bit of rust between armature and magnets.
It all cleaned up well. Now to get a new liner. Drive assy was a bit of a pain to remove.

 

[Stevetheboatguy]

Doc's 064 pics lit a fire under my arse......


Ohhsixysix. Been a long time waiting.

 

[a. palmer jr.]

On my bench right now is a friend's Husqvarna 435. I haven't taken any pics of it but when I opened it up I found a bunch of muddy water in the crankcase, sure don't know how it got there. I checked the fuel and oil tanks and they both look clean, must have come in through the muffler..

 

[Ronie]

Just got a Redmax G3800 with an oiler problem, once I get the oiler working I'm going to see if I can get a little more power out of it.

 

[Maintenance Chief]

Just got a Redmax G3800 with an oiler problem, once I get the oiler working I'm going to see if I can get a little more power out of it.

View attachment 328537 View attachment 328538

I'm not sure if you can squeeze more out of that one! It's already got the sticker.

 

[Ronie]

I'm not sure if you can squeeze more out of that one! It's already got the sticker.

lol

 

[drf256]

No elasto start ,no button? Your a braver man than I.

Better?

I have to retard the timing on this thing before even attempting to start it. It’s definitely feeling like one of the worst I’ve done for starting, and that’s with the elastostart.

 

[RI Chevy]

Time for a lektrik start model.

 

[qurotro]

It seems those 064 are aggressive even stock.

 

[drf256]

Plan C, more realistic.