What's on your bench?

[WillG]

Great success with the Excel pressure washer. Just need to test with hose and gun when I have more light and it's not raining.

Sent from my E6910 using Tapatalk

 

[WillG]

Tested the Excell and it did good except for a leaky gun which I recommended for replacement to the customer. His generator is up next for an oil leak diagnosis, it seems to be the rear main crank seal. If it is I'll recommend he take it to the local generator/electric motor repair place as I don't get involved in disassembly of generator heads. Also realized that the shop is starting to look like a real small engine repair place.....a good problem I guess...

Sent from my E6910 using Tapatalk

 

[dall]

Tested the Excell and it did good except for a leaky gun which I recommended for replacement to the customer. His generator is up next for an oil leak diagnosis, it seems to be the rear main crank seal. If it is I'll recommend he take it to the local generator/electric motor repair place as I don't get involved in disassembly of generator heads. Also realized that the shop is starting to look like a real small engine repair place.....a good problem I guess...

Sent from my E6910 using Tapatalk

the only difference is a tapered shaft
pull the cap off the end theres a center bolt loosen it and use a puller
they are not to difficult

 

[MustangMike]

Pics of the weird MS 880 muffler and set up. Two clips held in place with a steel spring clip! Muffler looks to be one piece, thick, cast aluminum.

 

[MustangMike]

Scored P+C was a little worse than I expected, with noticeable reduction in diameter of the piston top. However, no groves in cylinder, so it should clean up.

Hope none of the metal go in the bearings, I will flush it well. Sorry cylinder pic was not clearer, transfer actually started to close Ex port!

 

[MustangMike]

MS 880 cylinder is a Mahle. The transfers look excellent, the Ex could be a little wider and the In a little lower (I'm sure).

It has a circled A on the base, upper left is "1", upper right is "5", lower left is "0", lower right is "20". Can anyone tell me if these #s mean anything?

 

[WillG]

the only difference is a tapered shaft
pull the cap off the end theres a center bolt loosen it and use a puller
they are not to difficult

Thanks for the information however I already discussed that with the customer.

Sent from my E6910 using Tapatalk

 

[Canadian farm boy]

572xpw getting ported. I like porting these saws.

 

[a. palmer jr.]

I have a couple of Poulans, one a 306A and a newer Wild Thing plus a Dolmar 510 to check out. I still haven't found all my tools from the move but I'm getting there. Maybe get these running before they're needed...

 

[WillG]

Lapped the valves on the Generac cylinder head. Came out great. Changed the oil and filter on this Craftsman generator but it wouldn't start yesterday. It'll be on the bench tomorrow. Had 2 generators dropped off for repair yesterday as well. I better get my butt in gear.

Sent from my E6910 using Tapatalk

 

[Backtroller]

Picked up 2 201c-em today. 2017 and 2018. Needing a brake band for one. Both Mtronic. Both run well. They are sort of cool little saws. Very light.

 

[redlight066]

One of my customers came in today to pick up a couple of saws. They were in for some light maintenance and service. He says “I got something to show ya” with a BIG grin....

Kevin @huskihl this thing rips. Fine work sir.

 

[huskihl]

One of my customers came in today to pick up a couple of saws. They were in for some light maintenance and service. He says “I got something to show ya” with a BIG grin....
View attachment 256733
Kevin @huskihl this thing rips. Fine work sir.

Trying to think of whose it is. Not a Mark II?

 

[redlight066]

2018 550xp. 7.5hrs run time. 13% of the last hour was >12,000rpm

 

[huskihl]

2018 550xp. 7.5hrs run time. 13% of the last hour was >12,000rpm

Dull chain lol

 

[ayoungtexan]

Got a Echo 310 in getting a rebuild

 

[redlight066]

Dull chain lol

Nope. Bad ass saw

 

[redlight066]

He said it’s low on power. Lol. He’s 100% right.

 

[huskyboy]

He said it’s low on power. Lol. He’s 100% right.
View attachment 256790

Chinese or Brazil made bosch? The Chinese ones are horrid. One made it about a month on our 390xp before it ran like crap. I toss them for ngk or champion as soon as I see them now.

 

[redlight066]

I don’t think this is what heli coil had in mind for this application. Lol. The hits just keep on ah comin’