The SCARR Husqvarna 592XP build thread.

[Duane(Pa)]

Not enuff looooob

Oil thread!

 

[TreeLife]

Ok.....but GFY.

Lol...boop

 

[Ketchup]

@srcarr52, any potential to stroke one of these?

 

[Hinerman]

With a short bar my ported 395 kills it, with the unlimited coil the 395 cuts at around 12-12.5k rpm. I think the 395 might have a slight edge with overall power and would probably take the 592 with a long bar as well.

I know we ask a lot, but do you have a ported 390 to compare it to? I have my doubts about it hanging with a nice 390

 

[srcarr52]

I know we ask a lot, but do you have a ported 390 to compare it to? I have my doubts about it hanging with a nice 390

I've never ported, owned or even ran a 390.

 

[MG2186]

I've never ported, owned or even ran a 390.

Do you have any plans to do any more R&D on these or you just calling it good?

 

[huskihl]

I know we ask a lot, but do you have a ported 390 to compare it to? I have my doubts about it hanging with a nice 390

 

[MG2186]

I know we ask a lot, but do you have a ported 390 to compare it to? I have my doubts about it hanging with a nice 390

Have you ran a 592? I ran the one Kevin did and it’s quite a saw to be honest.

 

[Hinerman]

Well done Kevin. That seemed pretty even, slight edge to the 592, imo...

 

[Hinerman]

Have you ran a 592? I ran the one Kevin did and it’s quite a saw to be honest.

No sir, never seen one in person. That 592 in the video was clipping along, sounded angry too. Kevin does excellent work. We are privileged to have the saw builders/porters we have on this site.

 

[pbillyi69]

both of those saws were zippin right through that log. how did they feel compared to each other?

 

[huskihl]

Well done Kevin. That seemed pretty even, slight edge to the 592, imo...

Yeah about 2 seconds faster

 

[huskihl]

both of those saws were zippin right through that log. how did they feel compared to each other?

Hard to compare. The 592 wants to cut at a higher rpm. The limiting coil gets in the way a little. It’s probably very similar to one of my 390’s for a shorter bar. The guy I ported this 390 for likes torque for running a longer bar on it and didn’t want it rowdy.

 

[pbillyi69]

nice job

 

[Hinerman]

Yeah about 2 seconds faster

You need some sycamore logs for testing. I think that 592 would pull away; it was wanting to go. That petrified wood you get will hurt the pride of ANY saw imo

 

[huskihl]

You need some sycamore logs for testing. I think that 592 would pull away; it was wanting to go. That petrified wood you get will hurt the pride of ANY saw imo

A guy brought me up some red oak logs and cutoffs. Tis more better

 

[HYPERSAWS]

I've never ported, owned or even ran a 390.

You haven't lived

 

[srcarr52]

Do you have any plans to do any more R&D on these or you just calling it good?

The 592 is with its owner already. It will probably for to Joe eventually to get dyno’d.

The 585 is still here. I might mess with it more but I don’t have time right now.

 

[srcarr52]

You haven't lived

I’ve ran a stroked 395, I’ve lived plenty.

 

[MG2186]

The 592 is with its owner already. It will probably for to Joe eventually to get dyno’d.

The 585 is still here. I might mess with it more but I don’t have time right now.

Understandable, knowing how you are are, just figured you weren’t happy not getting big gains so figured you’d keep looking for more in them.