Saw video thread

[Wolverine]

Kinda' left the door open dinnja'? Jason sees the shot and takes it...

Jeff can be my wingman anytime.

 

[Fruecrue]

55 Rancher with 028 super piston, no muffler.
Never ran it stock so don’t know how it feels.
Opinions?

 

[brshephard]

That clutch cover can barely keep up with all them chips your making.

 

[huskyboy]

55 Rancher with 028 super piston, no muffler.
Never ran it stock so don’t know how it feels.
Opinions?

I bet it gains the torque when you put a muffler on it

 

[p61 western]

Jeff can be my huskyman anytime.

Fixed

 

[Wolverine]

I bet it gains the torque when you put a muffler on it

What?

 

[TreeLife]

 

[Duane(Pa)]

55 Rancher with 028 super piston, no muffler.
Never ran it stock so don’t know how it feels.
Opinions?

Is it tuned to four stroke? I didn't hear any, so might ought to be careful....

 

[TreeLife]

@Deets066 your muffler is on that there saw.

 

[RI Chevy]

Jeff can be my wingman anytime.

TY sir! [emoji106]

 

[Fruecrue]

Is it tuned to four stroke? I didn't hear any, so might ought to be careful....

Yes, plenty rich.
Tough to tell without a muffler.

 

[Deets066]

@Deets066 your muffler is on that there saw.

How ya like it?

 

[Deets066]

55 Rancher with 028 super piston, no muffler.
Opinions?

Gunna be honest.

Looks like *s-word

 

[Fruecrue]

Gunna be honest.

Looks like *s-word

Could be chit, could be too much chain.
I need to get a muffler and tune it.
It went together and fired right up, I just wanted to cut with it.

That’s a small saw pulling 18” of 3/8” full comp in hard wood and making big chips.
I’ll get more videos soon.

 

[TreeLife]

How ya like it?

Love love love it. Sounds sick!

 

[Chainsaw Jim]

Gunna be honest.

Looks like *s-word

Any saw can be made to look slow when maintaining that strong of a load on it.

 

[Deets066]

Could be chit, could be too much chain.
I need to get a muffler and tune it.
It went together and fired right up, I just wanted to cut with it.
View attachment 124548
That’s a small saw pulling 18” of 3/8” full comp in hard wood and making big chips.
I’ll get more videos soon.

Any saw can be made to look slow when maintaining that strong of a load on it.

I realize that fellas, hard to tell how a saw runs or feels from a video. With the right chain, muffler, and tune it might be a runner. But ya gotta admit... that vid didn't do it any justice.

 

[Fruecrue]

I realize that fellas, hard to tell how a saw runs or feels from a video. With the right chain, muffler, and tune it might be a runner. But ya gotta admit... that vid didn't do it any justice.

Agreed.
I’ll get her tuned right and out of that nasty crotch wood soon.

 

[huskyboy]

18” 3/8 on a 2253 in maple. Muffler mod and timing advance. .325 is a tad faster on it I think, but have not compared the two chains directly in the same log. But no problems pulling or oiling this 3/8 setup and it lasts longer.

 

[smokey7]

That 55 sounded good till it got so much load on it. It was being pulled down right to clutch stall. With a super aggressive chain like that you may jave to hold it up/back a bit to keep the revs up in the powerband. How well did the 028 piston fit?