HUSQVARNA HUSQVARNA THREAD

[ErnieG]

435 and 440 have a groove in the clamshell for the seals.

View attachment 455442

Mark

I sorta figured I had to but was not sure .
Thanks very much
Ernie

 

[hacskaroly]

Digging through a box of junk parts, came across this 372 crankshaft, the clutch side has been damaged, in your opinions is it damaged beyond use? I fit an e-clip on it, tried to spin it around to see if it would pop off and it didn't, but that isn't to say it won't at 8-10k rpm.

 

[popopboat]

Does crankshaft from Husqvarna 340,345,350 and Jonsered 2141, 2145, 2150 fit on 346xp?

Some shop sites say that it fits, some say that i doesnt.

 

[Woodslasher]

Digging through a box of junk parts, came across this 372 crankshaft, the clutch side has been damaged, in your opinions is it damaged beyond use? I fit an e-clip on it, tried to spin it around to see if it would pop off and it didn't, but that isn't to say it won't at 8-10k rpm.

View attachment 455471
View attachment 455472

Run it. I've got saws that look like that that have gone years without issue.

 

[Woodwackr]

Digging through a box of junk parts, came across this 372 crankshaft, the clutch side has been damaged, in your opinions is it damaged beyond use? I fit an e-clip on it, tried to spin it around to see if it would pop off and it didn't, but that isn't to say it won't at 8-10k rpm.

View attachment 455471
View attachment 455472

Hit it with a few tack welds and clean it up with a Dremel? Id try that before tossing it.

 

[hacskaroly]

Run it. I've got saws that look like that that have gone years without issue.

Sounds good, the crank is in really good shape otherwise!!

Hit it with a few tack welds and clean it up with a Dremel? Id try that before tossing it.

I have a welder now, will have to practice some before I make it even worse

 

[Woodwackr]

Sounds good, the crank is in really good shape otherwise!!

I have a welder now, will have to practice some before I make it even worse

Bah…that’s what grinders are for

 

[qurotro]

Digging through a box of junk parts, came across this 372 crankshaft, the clutch side has been damaged, in your opinions is it damaged beyond use? I fit an e-clip on it, tried to spin it around to see if it would pop off and it didn't, but that isn't to say it won't at 8-10k rpm.

View attachment 455471
View attachment 455472

Dropped on the ground.

 

[qurotro]

Does crankshaft from Husqvarna 340,345,350 and Jonsered 2141, 2145, 2150 fit on 346xp?

Some shop sites say that it fits, some say that i doesnt.

NO. Plastic saw crank does not fit mag case saw.

 

[popopboat]

NO. Plastic saw crank does not fit mag case saw.

Ok, thank you.
From what models does it fit then? Only 346xp?

 

[92TRX300FW]

Ok, thank you.
From what models does it fit then? Only 346xp?

only 346

 

[qurotro]

Ok, thank you.
From what models does it fit then? Only 346xp?

346 or 353. Or their Johnsered friends.

 

[qurotro]

Digging through a box of junk parts, came across this 372 crankshaft, the clutch side has been damaged, in your opinions is it damaged beyond use? I fit an e-clip on it, tried to spin it around to see if it would pop off and it didn't, but that isn't to say it won't at 8-10k rpm.

View attachment 455471
View attachment 455472

Fit the e clip on and shove some JB Weld on it . Call it a day.. Heat the glue if uninstall is needed lol.

 

[qurotro]

Ok, thank you.
From what models does it fit then? Only 346xp?

They are not the same. Gap between two bearings is not the same. Wel…if you can machine it.