Another chainsaw dyno...

[RI Chevy]

Deep Breaths Mike...lol

 

[MustangMike]

the filters on both the 462 and 500 hasnt been cleaned in a while unless joe did it
plus sharp chains make less smalls

I did clean the filter on the Asian 660 before it went to Joe … hope that is OK!

 

[MustangMike]

Deep Breaths Mike...lol

So Jeff, I know you did not make a bet, but what Hp do you think my saw will make … you saw it at the GTG and just some muff mods and break in since then.

 

[RI Chevy]

I don't gamble. I just run the saws and go by feel. Seat of the pants feel. Your saw was strong.
Cut well.

 

[huskihl]

They both filter fine

GASP!!

 

[huskihl]

Joes gonna be a bit yet. Having trouble getting his German dyno to understand Mandarin

 

[RI Chevy]

Does the DYNO accept saws with names?

 

[Deets066]

Does the DYNO accept saws with names?

Only if the name isn’t racist

 

[RI Chevy]

Good deal. Lol

 

[Deets066]

P.I.T.A. Is gunna file a lawsuit against Mike for animal cruelty.

 

[RI Chevy]

LMFAO

 

[huskihl]

Lol

 

[jk14]

Flying tiger bets-

Deets 8.1
Tree life 7.5 and less than hybrid
Mason 8
Mdavlee 8.2
M Mike 9.5
Wolverine 8.3
Spladle160 7.9
Jk14 8.4
Dall 7.5

Hybrid bets-

Mdavlee 8.9
Deets 9.175
M Mike 8.8
Wolverine 8.5
Spladle160 7.2
Jk14 9.1
Dall 9.5

Damn didn't even give me a full tenth
Gonna have to change my number

Flying tiger bets-

Deets 8.1
Tree life 7.5 and less than hybrid
Mason 8
Mdavlee 8.2
M Mike 9.5
Wolverine 8.3
Spladle160 7.9
Jk14 8.4
Dall 7.5

Hybrid bets-

Mdavlee 8.9
Deets 9.175
M Mike 8.8
Wolverine 8.5
Spladle160 7.2
Jk14 9.075
Dall 9.5

 

[huskyboy]

So it took a stihl with 10 more cc to beat a 372?[emoji23]

A well done 51.4mm 372xpw or a real good 7900/7910 will edge out that 500i in horsepower... probably just baaareely though. Considering the 500i is always “tuned” right with the fuel injection... that power should be repeatable and consistent. That’s a impressive 80cc saw right there.

 

[dall]

A well done 51.4mm 372xpw or a real good 7900/7910 will edge out that 500i in horsepower... probably just baaareely though. Considering the 500i is always “tuned” right with the fuel injection... that power should be repeatable and consistent. That’s a impressive 80cc saw right there.

send a saw then slacker

 

[rogue60]

And the winner is...

 

[huskyboy]

send a saw then slacker

I got nothin’ here that will beat that 500i in 5 cube. Lol. Except maybe a strong ms460 or my self ported 7900... but those are maybe 7.5 - 8.5hp saws and those are optimistic guesses. Strong enough for me, but most likely not good enough to beat a fuel injected monster with machine work. Especially after seeing what it did to that 462.

 

[Deets066]

681 or 7910 will end up being top dawg in the 5 cube.

 

[huskyboy]

681 or 7910 will end up being top dawg in the 5 cube.

Yep and ported by someone who is not me using tools someone can buy from Lowe’s. I’ll just make up for it with the chain at the gtg’s... Lol

 

[dall]

681 or 7910 will end up being top dawg in the 5 cube.

we havent seen results of your hybrid yet