What's on your bench?

[mdavlee]

107 is too low, on an 044 I like 103-101

For sure. 102 and leave the transfers alone on that one maybe. Or shape them differently. I take at 78-80

 

[BonScott46]

For sure. 102 and leave the transfers alone on that one maybe. Or shape them differently. I take at 78-80

Could get a nice running unit with a basic grinder.

 

[Deets066]

Could get a nice running unit with a basic grinder.

You could get decent numbers, but it’s still AM

 

[kingOFgEEEks]

Funny that you mention that .... Our anniversary did fall during our trip!!!!

Took her and the boy to Canadian side of Niagara falls ( falls view room) set up a saw deal before and picked up after. [emoji6]

Sent from my XT1635-01 using Tapatalk

Eventually the good wives come to accept it. If she does, she's a keeper.

 

[MG porting]

Depends on who you listen to, not necessarily.

I would make the Ex close to 100 and the In 75-80.

Sometimes, high compression (low exhaust) will limit RPMs and reduce power.

Well I was scratching my brain a lot last night and I was pretty tired when I was checking the port timing so I set everything up again like that's hard to do. Lol I guess it is when you're tired I mest up good thing I reached I have you guys to thank for that. Ex-98 & IN-79 TR-120. So how tired was I I guess pretty dang tired How's these numbers the exhaust seems low now? Intake is fair transfers good what do you guys think?

 

[Deets066]

Well I was scratching my brain a lot last night and I was pretty tired when I was checking the port timing so I set everything up again like that's hard to do. Lol I guess it is when you're tired I mest up good thing I reached I have you guys to thank for that. Ex-98 & IN-79 TR-120. So how tired was I I guess pretty dang tired How's these numbers the exhaust seems low now? Intake is fair transfers good what do you guys think?

I’d drop the jug about .020-.025 and run it.

 

[MustangMike]

I'd leave those #s just where they are, but I would double check them, that is a big difference.

 

[Deets066]

I'd leave those #s just where they are, but I would double check them, that is a big difference.

They aren’t bad numbers at all, needs a little compression bump though

 

[drf256]

Finished @trooney Hybrid jug. Fingers came, meh...

My fault for not drinking. Im not sure how to port without beer.

 

[drf256]

 

[drf256]

 

[Fruecrue]

Looks real good Al!

 

[usmcbuckwild]

Damn, Doc. You do nice work

 

[MustangMike]

Nice Al, will be watching to see how this one runs.

 

[Wolverine]

Daggum, now I have to tear apart all my saws and check the clip orientation.







































NOT!!

 

[huskyboy]

 

[drf256]

A hybrid is born!

 

[MG porting]

I’d drop the jug about .020-.025 and run it.

Can't drop it anymore than I have its right where it is. Lol

 

[MG porting]

I'd leave those #s just where they are, but I would double check them, that is a big difference.

I reached and for some reason my numbers were way off last night I do have a habit of pushing myself to far and it showed last night even my lady asked me if I was OK. Lol so this saw should be a good running saw you think?

 

[MG porting]

View attachment 152521 View attachment 152522 View attachment 152523 View attachment 152524 View attachment 152525

Very nice work I really want to try out finger ports one day.