What's on your bench?

[MustangMike]

The MS 460 they told me had a ceased crank only had an imploded clutch, nothing else wrong with it. However, that clutch was a PITA to get off!

 

[p61 western]

P61

I have metal worm gears for the earlier 415 475 and jreds used and nos already. But they have a outer seal and smaller pto bearing. The later with plastic worm gear have the pto bearing and seal set up like 385 etc.

What I was wondering if the metal worm gear can be used somehow on the later ones for a fix for the guy. I know the oilers are the same for both.

I know the updated fix for the older ones was to go the other way. But now we need to see if it can go in reverse.

older and newer pto sides

View attachment 151328 View attachment 151329

I'm real curious to see what you come up with for this.

 

[Cut4fun]

I'm real curious to see what you come up with for this.

I could go pull one of my 505 445 runners down to try it. Butttttttttt not right now in the cards.

Why hoping someone else tried it already.

 

[p61 western]

I could go pull one of my 505 445 runners down to try it. Butttttttttt not right now in the cards.

Why hoping someone else tried it already.

Last resort lol.

 

[Cut4fun]

I got a 415 in with the update and plastic worm gear in it back in Nov

 

[irving.lavoie]

Check out this old peace, running great just rebuild the carb

Sent from my Alcatel_6060C using Tapatalk

 

[tickbitintn]

Check out this old peace, running great just rebuild the carbView attachment 151334View attachment 151335View attachment 151336View attachment 151337

Sent from my Alcatel_6060C using Tapatalk

Nice!
That's a clean survivor.

Sent from my XT1635-01 using Tapatalk

 

[irving.lavoie]

Nice!
That's a clean survivor.

Sent from my XT1635-01 using Tapatalk

It's been sitting for years just start it up every now and again

Sent from my Alcatel_6060C using Tapatalk

 

[big t double]

It's winter and my new house doesn't have a heated spot to tinker on saws...so this stuffs made its way back to my inside bench. Boom Bap

 

[huskihl]

It's winter and my new house doesn't have a heated spot to tinker on saws...so this stuffs made its way back to my inside bench. Boom Bap View attachment 151338

Dj Heavy T is in the hizzle

 

[Czed]

Check out this old peace, running great just rebuild the carbView attachment 151334View attachment 151335View attachment 151336View attachment 151337

Sent from my Alcatel_6060C using Tapatalk

Those are good running saws
An old fella still runs one here
I went through it a few years back.
Good looking saws

 

[bigbadbob]

It's winter and my new house doesn't have a heated spot to tinker on saws...so this stuffs made its way back to my inside bench. Boom Bap View attachment 151338

BIG-T Rapper??

 

[DND 9000]

It's winter and my new house doesn't have a heated spot to tinker on saws...so this stuffs made its way back to my inside bench. Boom Bap View attachment 151338

Cool, I also do a little bit of DJing.

 

[big t double]

BIG-T Rapper??

Cool, I also do a little bit of DJing.

Nah I'm no rapper or dj...I just mess around makin little beats for a couple buddies to rhyme over. Used to have protools and recorded a little bit but that computer took a *s-word so back to basics. Samples and the mpc.

 

[usmcbuckwild]

MS271

Widened out the intake just a bit (DO NOT REMOVE THE LITTLE NIPPLE IN THE INTAKE, IT SUPPORTS THE RING AND RING PIN), cleaned up the lower transfer port opening and streamlined it a bit, widened the exhaust and cleaned up the oogly casting in the exhaust port. Matched the heat plate and muffler inlet to the exhaust and modded the outlet inside the factory hood/deflector. Bumped the timing just a touch (.010) and made the carb adjustable.

Runs pretty darn good. Have to put it in wood later and fine tune it.

 

[mikerudder]

Piecing together a 460 that I got in a box of parts

It was straight gassed, so I pulled it all apart and cleaned it up. Piston was shot but cylinder cleaned up. Looks low hour to me?



It came with a non HD filter setup - got the parts in to convert it, but the carb studs are too short? Anyone know the PN? I came up with 1128 122 6603. Just curious as to how long those are? I don’t want to order the wrong ones. ( 2 3/8” or 60mm approximately)




Also curious which tank vent I need?

 

[MustangMike]

I've already used all my 460 tank handles or I would measure one for you. I'm sure a dealer will chime in.

The tank vent is widely available, the AM ones seem to work just fine. Looks like yours is missing the top half, they just pop in and out.

https://www.ebay.com/itm/10-Tank-Ve...epid=1179049645&hash=item3f8da614c1:rk:1:pf:0

 

[Woodrow]

Not on the bench, just above it. Heat in the garage!

I like it! What brand and model is it? Looks like it is electric, assuming 220?

 

[Sty57]

I have heard of a fair number of guys trying them, never heard any good reports yet, plenty of bad reports though.

So how long are they lasting?
5mins, 1hr, 5hrs or more?

I would think 5hrs would be a ton of run time on a race saw.

 

[Duane(Pa)]

So how long are they lasting?
5mins, 1hr, 5hrs or more?

I would think 5hrs would be a ton of run time on a race saw.

It really comes down to what oil and what ratio you run...