What's on your bench?

[heimannm]

I am going through my Power Mac 6 parts saws this week. Took several apart, getting everything cleaned up, I'll put together two or three runner and keep the other parts for those in need. They're spread out over a couple of benches at this point.





Mark

 

[PA Dan]

I am going through my Power Mac 6 parts saws this week. Took several apart, getting everything cleaned up, I'll put together two or three runner and keep the other parts for those in need. They're spread out over a couple of benches at this point.

View attachment 289727

View attachment 289728

Mark

Wow Mark... I got a couple trying to make a runner out of too!

 

[Canadian farm boy]

Rebuilding and porting a 395xp. It’s 90% done. Just waiting on a couple small parts and I can get it in wood for a test run.

 

[Saw_Squatch]

Picked up a barely used 28" stihl bar for only $40. Only other thing I think I want to do on this 044 is throw a maxflow on it

 

[MustangMike]

I've been running the steel screen winter filter on mine, cleans up real fast!

Would not use it for milling, but when making decent chips I think it works just fine.

 

[MustangMike]

FYI part # 0000-120-1653 and it comes with the anti spit back foam.

 

[a. palmer jr.]

The only things on my bench now are two old Stihl saws, an 028 which I've been told has an air leak and an 011AV which we can't get to start and I suspect has a scored cylinder and a stuck ring or two. On the 011 I put a small amount of fuel down the spark plug hole and tried to start it with no luck (it has plenty of spark). Haven't messed with the 08 yet.

 

[WillG]

Echo TC2100 tiller got a new OEM Zama carb and spark plug. Didn't have to touch the carb except for dropping the idle speed a little bit. Did some tilling with it and it ran perfectly. Dropping it back off to him tomorrow.

Got a free low hours/very well taken care of Toro 521 snowblower today for free from the bosses friend. He says it'll run for a bit then flood out. Should be an easy money maker in the fall.

This small engine repair stuff is a pretty good racket!! Easy money!!

Sent from my E6910 using Tapatalk

 

[Maintenance Chief]

Echo TC2100 tiller got a new OEM Zama carb and spark plug. Didn't have to touch the carb except for dropping the idle speed a little bit. Did some tilling with it and it ran perfectly. Dropping it back off to him tomorrow.

Got a free low hours/very well taken care of Toro 521 snowblower today for free from the bosses friend. He says it'll run for a bit then flood out. Should be an easy money maker in the fall.

This small engine repair stuff is a pretty good racket!! Easy money!!

Sent from my E6910 using Tapatalk

Easy for the patient and knowledgeable!
Good job Will.

 

[WillG]

Easy for the patient and knowledgeable!
Good job Will.

Thanks!

Sent from my E6910 using Tapatalk

 

[WillG]

Got the Weber cleaned and fired up for the season. Added a thermometer as well.

Sent from my E6910 using Tapatalk

 

[WillG]

First use of the Weber was a success.

Sent from my E6910 using Tapatalk

 

[huskihl]

Got the Weber cleaned and fired up for the season. Added a thermometer as well.

Sent from my E6910 using Tapatalk

In about two years only half of the burner will want to stay lit. I drilled out every hole in the burner about .1mm bigger, just as a last resort, as I was about to give up. Got lotsa fire now lol

 

[Kiwioilboiler]

In about two years only half of the burner will want to stay lit. I drilled out every hole in the burner about .1mm bigger, just as a last resort, as I was about to give up. Got lotsa fire now lol

How do XS stickers hold up on ported BBQs Kev?

 

[huskihl]

How do XS stickers hold up on ported BBQs Kev?
View attachment 289899

Maybe better than your crocs?

 

[Kiwioilboiler]

Maybe better than your crocs?

The bare foot? No crocs here bro....Jandals, just not in the house which the patio is off.

 

[WillG]

In about two years only half of the burner will want to stay lit. I drilled out every hole in the burner about .1mm bigger, just as a last resort, as I was about to give up. Got lotsa fire now lol

She's just over 3 years old now. When I first fired her up last weekend she wasn't burning good. Took and wire wheeled and scotch brited the burner tube and hit it with compressed air. She burns good now. Got up to 500F in no time at all. Might port it at some point

Sent from my E6910 using Tapatalk

 

[Ronie]

Got a muffler mod done and started on a cylinder for my 562.

 

[davidwyby]

Got the transfer out of the 450 cyl. Accidentally Beveled the port a bit. Still need to polish/hone. Also still looking for a piston.

 

[a. palmer jr.]

Echo TC2100 tiller got a new OEM Zama carb and spark plug. Didn't have to touch the carb except for dropping the idle speed a little bit. Did some tilling with it and it ran perfectly. Dropping it back off to him tomorrow.

Got a free low hours/very well taken care of Toro 521 snowblower today for free from the bosses friend. He says it'll run for a bit then flood out. Should be an easy money maker in the fall.

This small engine repair stuff is a pretty good racket!! Easy money!!

Sent from my E6910 using Tapatalk