What oil is best? and what ratio?

[Moparmyway]

I believe u on that fuel quality. How do u buy yours ? 5 gal. Pail?

Yup

 

[Keith Gandy]

Yup

That is the fuel without oil?

 

[Moparmyway]

That is the fuel without oil?

Yes Sir, I preferr knowing what oil I am mixxing

 

[Keith Gandy]

Yes Sir, I preferr knowing what oil I am mixxing

I figured as much but wanted to make sure. Any place better than another to buy the fuel? This question about fuel has been pondering my mind man!! Thanks

 

[Moparmyway]

I figured as much but wanted to make sure. Any place better than another to buy the fuel? This question about fuel has been pondering my mind man!! Thanks

I check Amazon and E-Bay and just grab whomever has the best price delivered

 

[KenJax Tree]

Damn you get robbed online....2 dealers here sell it for $69

 

[Moparmyway]

Damn you get robbed online....2 dealers here sell it for $69

I'm sure shipping from "Over there" to over here would add too much to the cost.
Even the dealer sells it for over $100 for 5 gallons ................ NY is the rip-off capital of the NE

 

[KenJax Tree]

Yeah when you consider the weight and hazmat fee's shipping is expensive

 

[LowVolt]

Why do I continue to read? That is the better question.

 

[mdavlee]

Yeah when you consider the weight and hazmat fee's shipping is expensive

$78 for 5 gallon can delivered to me. They added another $8 shipping for rural. They delivered it to town since they had it on a 53' box trailer.

 

[junkman]

You guys realize the extra money spent on special fuel and oil after a while the savings using cheap stuff would buy you another saw before it is wore out right ?

 

[DSS]

You guys realize the extra money spent on special fuel and oil after a while the savings using cheap stuff would buy you another saw before it is wore out right ?

Reported

Moderators, do we need this clown trying to kill the thread?

27.88:1 goose grease FTW

[emoji202] [emoji106] [emoji106] [emoji1]

 

[big t double]

Why do I continue to read? That is the better question.

I ask myself the same thing, but yet I continue to read it....on another note, check me out rory...I avatared up finally hahahahaha!!!

 

[Keith Gandy]

Instead of the high $$$ fuel I wonder about one of these?

http://www.walmart.com/ip/16647989?...5448329&wl4=&wl5=pla&wl6=161071186849&veh=sem
http://lucasoil.com/products/fuel-treatments/lucas-oil-deep-clean-fuel-system-cleaner

 

[LowVolt]

I ask myself the same thing, but yet I continue to read it....on another note, check me out rory...I avatared up finally hahahahaha!!!

Yes i see that. WU-TANG? I liked your old one better...

 

[big t double]

Yes i see that. WU-TANG? I liked your old one better...

well I supposed I could go back to the ol circle with the arrow. just for you hahaha

 

[Redbull661]

https://www.klotzlube.com/Ecommerce/site/content/PDFs/TECH/KL-200-Tech-Sheet.pdf

Noticed on the original Techniplate spec sheet, that it said a 13,000 max rpm. Figured I'd call them and see why...

Guy I talked to said, that was the point in their testing where the viscosity of the oil started breaking down...something about scraping molecules off the cylinder walls.

I know some guys here have used it higher than 13k. I'm just repeating what the guy told me. Klotz Tech phone # is 260-490-0489 if anyone else wants to call them.

 

[Keith Gandy]

https://www.klotzlube.com/Ecommerce/site/content/PDFs/TECH/KL-200-Tech-Sheet.pdf

Noticed on the original Techniplate spec sheet, that it said a 13,000 max rpm. Figured I'd call them and see why...

Guy I talked to said, that was the point in their testing where the viscosity of the oil started breaking down...something about scraping molecules off the cylinder walls.

I know some guys here have used it higher than 13k. I'm just repeating what the guy told me. Klotz Tech phone # is 260-490-0489 if anyone else wants to call them.

Ive ran upwards of 16000 on 2 of my saws with it. Not a scratch in the cylinder or a blue mark

 

[Keith Gandy]

One other thing to consider. How many of us have saws that turn a constant 13000 in cut

 

[Redfin]

Ive ran upwards of 16000 on 2 of my saws with it. Not a scratch in the cylinder or a blue mark

Looks like you need to keep the pizz revving under 13 Keith.