So what did you do today?

[larasea]

New Landpride grapple, RG1060. Traded in my Blue Diamond after 6 years of use. Nice upgrade.

 

[Sloughfoot]

never used SLIP, but I have used EZ Slide graphite paint in the past. It worked good, but you always had to re-apply it and now I can't find it locally (sold by Tractor Supply). I went with some $12 rustoleum oil base flat black this time.

I put a thick coat of SLIP on mine last fall. Hoping grass won't stick to it as much as it did to paint.

 

[SawAddictedFarmer]

I got the the frame rolled out from under the body on my 4runner. Now I just have to do a little welding and strip prime and paint it.

 

[furb]

Dug this out of the tool dump. Three drawers were in front of another building half buried and this was in the back of a junk truck. It was swayed enough from falling that the drawers probably didn’t slide and likely why it was apart. I beat it back to almost square. The missing drawer, slides and top struts are ordered.

 

[legdelimber]

I've seen some angle iron used to span the box and then a handful of bar clamps on the ends of the angle iron, pull a couple of tool cabinets back fairly well.

 

[furb]

I've seen some angle iron used to span the box and then a handful of bar clamps on the ends of the angle iron, pull a couple of tool cabinets back fairly well.

I put a 2x4 on the bottom of the right side then beat on another 2x4 on the top left. I should have used a gentler method but that rusty fiskars sledge had a good wack to it. I clamped a Waterloo to a bench, clamped a piece of angle to pry against and straightened one that way but all my benches are buried with crap right now.

 

[singinwoodwackr]

Got another member's 350 back together and running.
Gonna take a bit to seat the new ring.

 

[furb]

I was told I rented too small of a machine but I still got this out.

 

[singinwoodwackr]

For some odd reason, this 350 runs/cuts way better with a fuel filter that actually flows fuel.

 

[furb]

Got another member's 350 back together and running.
Gonna take a bit to seat the new ring.
View attachment 486161

For some odd reason, this 350 runs/cuts way better with a fuel filter that actually flows

Those are still my favorite saws for some reason

 

[jblnut]

Took delivery of an EAVision J150 spray drone and a Winco 22kw generator.


One blade set is wider than a 5th grader !!


The controller is rather girthy as well.

 

[singinwoodwackr]

Took delivery of an EAVision J150 spray drone and a Winco 22kw generator.
View attachment 486290

One blade set is wider than a 5th grader !!
View attachment 486291

The controller is rather girthy as well.
View attachment 486292

So…all those stories about alien spacecraft or Chinese spy drones…it was you ?

 

[singinwoodwackr]

Those are still my favorite saws for some reason

I might even assemble the one I have in a box now
Just need a piston.
I do have a model 50, 45mm nos piston that is the same size as the 350, just flat instead of dished. Will experiment… otherwise, meteor if I can’t find a cheap oe one.

This saw wound up with 150#, cold comp with new Caber ring which ain’t bad. No base gasket, .019 sq. Opened up the ex port and lower transfers to match the base, muff mod.

 

[Bill G]

......gotta bring the skidloader back up to lift the 955 deck, 450lbs vs my 198lbs ain't happening.

The only time I see 198lbs on the scale is when the dial spins by

 

[jblnut]

So…all those stories about alien spacecraft or Chinese spy drones…it was you ?

Just got it today. I’ll be in future headlines.

 

[Bill G]

So…all those stories about alien spacecraft or Chinese spy drones…it was you ?

I need to buy one and fly into a trailer park. It will be hilarious as they brag about being "anal probed"

 

[singinwoodwackr]

The only time I see 198lbs on the scale is when the dial spins by

Too much bacon…

 

[singinwoodwackr]

Just got it today. I’ll be in future headlines.

You and your future heart breaker?
Too cute!

 

[EFSM]

Took delivery of an EAVision J150 spray drone and a Winco 22kw generator.
View attachment 486290

One blade set is wider than a 5th grader !!
View attachment 486291

The controller is rather girthy as well.
View attachment 486292

You sure pull out all the stops. Nice setup.