So what did you do today?

[PA Dan]

Never seen so much dirt in a bathtub.
Could be corrupting my poor kid

The exact opposite my friend the exact opposite! Keep up the good work![emoji106][emoji106]

 

[Wolverine]

Strapped one of my 2 wheelers to the dyno today.

 

[Wilhelm]

Gave my Super A a wash down, tune up and changed the oil. I’ll be using it to run a PTO pump for Joe’s splitter later this evening. Some of you know that this tractor was owned by my grampa for just under 30 years, he’s been gone since 2010.

View attachment 128540 View attachment 128541 View attachment 128542

That off-set engine design looks funky (3rd picture).
Nice tractor.

 

[XP_Slinger]

That off-set engine design looks funky (3rd picture).
Nice tractor.

It sure does! Lol! That offset was a feature they called “Cultivision”, it allowed for a better view of the cultivators while running rows. Not a great feature for a woods tractor though, you can’t see the left front tire without leaning way out which is a little inconvenient when you get into tight quarters.

 

[XP_Slinger]

Got a good start on a brick patio in our back yard. Lots of work to get to this point!

Sent from my SM-G892A using Tapatalk

Looking great! I used 16” pavers for a 10’x14’ patio at our old place in VA, very time consuming but what a nice area once it was done. I feel your pain

 

[Wilhelm]

I did my work clothes laundry.
Also sorted some scrap metal, brass , aluminum and tooling steel.

I discovered that the roof above my dad's "shop" is leaking badly, didn't climb the roof to take a look as it started pouring like someone cut open the sky.
That leak has to be fixed, everything sitting on the ground is soaked, so is the floor concrete.

 

[hoskvarna]

I did my work clothes laundry.
Also sorted some scrap metal, bras , aluminum and tooling steel.

I discovered that the roof above my dad's "shop" is leaking badly, didn't climb the roof to take a look as it started pouring like someone cut open the sky.
That leak has to be fixed, everything sitting on the ground is soaked, so is the floor concrete.
View attachment 128968

And why are you sorting bra’s[emoji33]


Sent from Hoskey Hills

 

[beaglebriar]

And why are you sorting bra’s[emoji33]


Sent from Hoskey Hills

Must be a rather large collection??

 

[Bigmac]

Strapped one of my 2 wheelers to the dyno today.

View attachment 128925

What did you do to it? What bike is it?

 

[Wilhelm]

And why are you sorting bra’s[emoji33]


Sent from Hoskey Hills

Gotta sort them by size so I can stack 'em one atop another, double-D on top!
.
.
.
Stupid autocorrect had a hiccup and I didn't catch it.
Fixed it now, it was supposed to say "brass".

Must be a rather large collection??

I wish . . .

 

[hoskvarna]

Gotta sort them by size so I can stack 'em one atop another, double-D on top!
.
.
.
Stupid autocorrect had a hiccup and I didn't catch it.
Fixed it now, it was supposed to say "brass".


I wish . . .

Figured that
But had give ya chit [emoji106]


Sent from Hoskey Hills

 

[Wolverine]

What did you do to it? What bike is it?

Gave it a proper tune up before the run. Clean k&n, fresh plugs, calibrated the tps. I’ve never had an a/f curve to see so I was curious. It has shortened am pipes. That’s all. Found I need to shim the needles a little but she’s good to go. It’s a Honda VTR1000f, Superhawk. 996 twin.

 

[Bigmac]

Gave it a proper tune up before the run. Clean k&n, fresh plugs, calibrated the tps. I’ve never had an a/f curve to see so I was curious. It has shortened am pipes. That’s all. Found I need to shim the needles a little but she’s good to go. It’s a Honda VTR1000f, Superhawk. 996 twin.

Nice! So was the needle shim the difference in the two curves?

 

[Bigmac]

Got this motor all done yesterday and delivered it this morning and helped get it into the frame, he is waiting on suspension and a custom pipe.

Then I did some pressure washing and made a dump run!


Then I got this bike in and done, I had built the motor for him a few years back, but he did a chassis swap, with different carb and ignition, got that all tuned in, we are going to test it tomorrow!

 

[Wolverine]

Nice! So was the needle shim the difference in the two curves?

I can't upload pics at the moment (forum is wacked). That was the hp and torque plots. My a/f showed lean before it's fully on mains. So if I shim it up a tad, it'll give it some more fuel there.

 

[Wolverine]

@Bigmac bottom is a/f


And here’s what I’ve done today.

 

[Wilhelm]

Came home from work, waited for the high sun to set a little and mowed the whole lawn around my house.
Takes about 2-3 hours depending on how high the grass grew.

My walk behind mower is acting up, won't come down to idle - I'll have to look into it.

Hedges are on the schedule tomorrow, the one behind the house grew at least 3 meters high.

 

[Mastermind]

I've had the gas all day.

 

[Backtroller]

I used my stihl HS 82t hedge trimmer, my 201t and my polesaw today trimming all of my bushes and crab apple trees. Everything started and ran flawlessly so that was a bonus.

Sorry about your gas Randy. I feel for your wife

 

[MustangMike]

Got my Asian 440 Big Bore running today, but the damn thing is kicking my A$$. I'll post details in my Asian Triplets thread. I'm beat!