how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Hedgerow]

Sux , they have a long ways to go

Sent from my SM-G955U using Tapatalk

You vertical jigging?

 

[67L36Driver]

Diss Stihl all you want. It’s what sells quick in my neighborhood. [emoji108]

[emoji48]

Unless I want to spend $150 on a MS391 top end I’ll have to attempt to re seal the transfer port covers. [emoji90]

I’m very suspicious Stihl had to eat some MS311 factory defect leakers.

Only up side is, the 311 piston is interchangeable with the MS362. Save it for later.

I’m betting we break stuff.

 

[countryhog]

organizing files today and came across this. thought it might be good for s and g. you guys really got old

 

[MACHINE]

You vertical jigging?

Am right now

38 to 55 fow

Sent from my SM-G955U using Tapatalk

 

[Dub11]

 

[WKEND LUMBERJAK]

Dang drizzly and cold out.

 

[hoskvarna]

Snowing here now [emoji2959][emoji2959][emoji2959]


Sent from Hoskey hilltop

 

[Workshop]

Rainy and wet down here at the postage stamp.
Forecasting accumulating snow for here by Sunday. Hwy 60 corridor and South into Arkansas. I'm about 3 miles from Arkansas.

 

[JimBear]

Snowing here now [emoji2959][emoji2959][emoji2959]


Sent from Hoskey hilltop

No snow here yet, it’s been light rain most of the day since about 7:00 this morning. The are guessing it’s going to start about 10:00 tonight, also guessing between 2”- 4”.

 

[Only the Tony]

Sux , they have a long ways to go

Sent from my SM-G955U using Tapatalk

Have you seen the video released this week?

 

[MACHINE]

Have you seen the video released this week?

Yep, not as good to me , and last 3 lowrance units i have had failed ,


Sent from my SM-G955U using Tapatalk

 

[Only the Tony]

Yep, not as good to me , and last 3 lowrance units i have had failed ,


Sent from my SM-G955U using Tapatalk

So far I haven't had any major problems with mine. I was thinking of doing an entire switch out to garmin except that the force trolling motor currently doesn't have a long enough shaft. Running a carbon 12 at helm and HDS gen3 7 at bow networked with an Xi5 motor. Garmin has it going on with the wireless networking, but the price for a total upgrade and the short trolling motor shaft length puts them out of the running for a while. I think the next thing I need to get is a drotto.

 

[hoskvarna]

Still light snow and white on da ground


Sent from Hoskey hilltop

 

[Cat 525]

Moisture quit in the night! Hopefully stays away today!

 

[67L36Driver]

Morning midlanders!

Mulling over what to do with the MS311.

Since I can’t find where the air leak is (strongly suspect the glued on transfer covers.) maybe just part it out on Craigslist. [emoji848]

 

[Hedgerow]

So far I haven't had any major problems with mine. I was thinking of doing an entire switch out to garmin except that the force trolling motor currently doesn't have a long enough shaft. Running a carbon 12 at helm and HDS gen3 7 at bow networked with an Xi5 motor. Garmin has it going on with the wireless networking, but the price for a total upgrade and the short trolling motor shaft length puts them out of the running for a while. I think the next thing I need to get is a drotto.

Is that the tech equipment you use to move along a pre determined course while spoon bill fishing?

I assume it can hold you over a spot also?

 

[Hedgerow]

Morning midlanders!

Mulling over what to do with the MS311.

Since I can’t find where the air leak is (strongly suspect the glued on transfer covers.) maybe just part it out on Craigslist. [emoji848]

Have you pressure tested it yet Carl?

 

[Workshop]

Morning everybody.

 

[hoskvarna]

Moisture quit in the night! Hopefully stays away today!

Snowing hard right now here

Sent from Hoskey hilltop

 

[67L36Driver]

Have you pressure tested it yet Carl?

Nope. I lack all the proper block off plates plus it’s in a hundred pieces.

I could have Hack Horner guys test it. Wouldn’t be much trouble to assemble the basic engine for that.