how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Time's Standing Stihl]

You're 19? Little early in life to be bowing down! Grow a set and get the 3120!

Haha, G'luck with the 660 kit

 

[67L36Driver]

Got pissed off my girl was mad about the cost of the 3120 so I'm ordering the huztl ms660 kit. Wish me luck building it. lol

Order a decomp valve and set of clutch springs at your Stihl dealer for it.

Don't use the Chinese stuff.

 

[Homelite410]

My bil has a drolet and loves it! 10' of stack on it.

 

[Homelite410]

https://www.drolet.ca/en/products/stoves/ I think he has the spark.

 

[Ethan Hamby]

Order a decomp valve and set of clutch springs at your Stihl dealer for it.

Don't use the Chinese stuff.

I have no use for the decompression valve I will probably put a bolt in it. I'm gonna get a Stihl OEM tensioner also the huztl one is junk. Other than that they're pretty good parts. The ms390 cylinder kit I have sitting around is super nice from them

 

[Ethan Hamby]

I might put a decomp on just to have it but I don't need them lol the only saw I've found hard to pull start was a damn 55 rancher that had sat and the rings had seized somehow. Once I got it free tho it was easy again

 

[concretegrazer]

https://www.drolet.ca/en/products/stoves/ I think he has the spark.

The myriad/austrial/legend/baltic should all be easy starters with that bypass.

 

[huskihl]

One man saw. Only 35 lbs. 45cc.
That hurts just thinking about it.

We have one stuck through the wall at our hunting camp. It hurts just looking at one too

 

[Ethan Hamby]

I just wanna cut fast and not have people on my back *b-wording

 

[huskihl]

Got pissed off my girl was mad about the cost of the 3120 so I'm ordering the huztl ms660 kit. Wish me luck building it. lol

You're 19? Little early in life to be bowing down! Grow a set and get the 3120!

Haha, G'luck with the 660 kit

Something tells me brother Clinton has been down this road before.
Nonetheless, good advice. Or it'll only get worse

I'm gonna get a Stihl OEM tensioner also the huztl one is junk

I wouldn't say it's "junk", although I've also read where Walt felt it was weak. Grease it up really good and run it back and forth a few times. Unless it's used every day, it'll probably last a long time. I've put bars and chains on mine 50 times or so and it still works fine

 

[Ethan Hamby]

I use my saws daily most of the time

 

[Ethan Hamby]

I can order the ms660 and the Husqvarna 372 kit together for $512 that should be enough project for a few days lol

 

[Ethan Hamby]

Then I'll have my 60cc, a 75cc, and a 90cc

 

[Time's Standing Stihl]

Something tells me brother Clinton has been down this road before.
Nonetheless, good advice. Or it'll only get worse

My thoughts exactly!

 

[huskihl]

I can order the ms660 and the Husqvarna 372 kit together for $512 that should be enough project for a few days lol

I'd replace the wrist pin bearings with oem also

 

[Ethan Hamby]

I don't let her walk all over me she packed her *s-word to leave today because of it. But as always she backed out

 

[Ethan Hamby]

I hope it comes with steel case bearings instead of nylon

 

[Dub11]

Morning Y'all and Ethan have ypu.looked at saw for sale here on this site yet? I think In saw a 394 around 700

 

[Ethan Hamby]

No I haven't looked but I've got my mind set now I will love knowing I built my saw from parts

 

[Ethan Hamby]

I might even try my hand at port work on them. Those cylinders are cheap so it's no biggy if I *f-word up