dall
Mastermind Approved!
- Local time
- 8:38 PM
- User ID
- 795
- Joined
- Feb 5, 2016
- Messages
- 48,770
- Reaction score
- 201,574
- Location
- grafton wv
brads pole saw would be the one id want to see
Another chainsaw dyno...
- Thread starter Red97
- Start date
Time's Standing Stihl
Below me...
- Local time
- 8:38 PM
- User ID
- 1179
- Joined
- Apr 20, 2016
- Messages
- 11,248
- Reaction score
- 64,402
- Location
- Central Iowa
cuinrearview
Handy dood
- Local time
- 8:38 PM
- User ID
- 9248
- Joined
- Apr 16, 2019
- Messages
- 11,356
- Reaction score
- 78,962
- Location
- Dowling, MI
48mm KS. Popup. TA. No grinding. Ran mesh and flock filter. Not log around to immediately cut on.
- Local time
- 8:38 PM
- User ID
- 570
- Joined
- Jan 17, 2016
- Messages
- 8,096
- Reaction score
- 51,862
Which one? Fully erected?
500i right at 6.8 hp.
The dip at 10.5k is it deciding to richen way up. Think it was the light load at the high rpm. Get on it too hard it wont show the data.
dall
Mastermind Approved!
- Local time
- 8:38 PM
- User ID
- 795
- Joined
- Feb 5, 2016
- Messages
- 48,770
- Reaction score
- 201,574
- Location
- grafton wv
cuinrearview
Handy dood
- Local time
- 8:38 PM
- User ID
- 9248
- Joined
- Apr 16, 2019
- Messages
- 11,356
- Reaction score
- 78,962
- Location
- Dowling, MI
- Local time
- 8:38 PM
- User ID
- 2523
- Joined
- Jan 24, 2017
- Messages
- 4,960
- Reaction score
- 22,966
- Location
- Berkshire County, Massachusetts
One ported by someone with considerable experience with the model? Like from any of the porters on this site. There haven't been very many 79xx on the dyno other than the Egan saws, right @Red97 ?
Redfin
Meh...
- Local time
- 8:38 PM
- User ID
- 159
- Joined
- Dec 24, 2015
- Messages
- 7,645
- Reaction score
- 39,995
- Location
- Central Pa
I wouldnt mind seeing Mutt on there.
cuinrearview
Handy dood
- Local time
- 8:38 PM
- User ID
- 9248
- Joined
- Apr 16, 2019
- Messages
- 11,356
- Reaction score
- 78,962
- Location
- Dowling, MI
dustinwilt68
Wilt Built Work Saws
- Local time
- 8:38 PM
- User ID
- 1007
- Joined
- Mar 8, 2016
- Messages
- 5,933
- Reaction score
- 26,241
- Location
- Southwest PA
Shocked the 572 made more hp then the 500i, booth stock.
cuinrearview
Handy dood
- Local time
- 8:38 PM
- User ID
- 9248
- Joined
- Apr 16, 2019
- Messages
- 11,356
- Reaction score
- 78,962
- Location
- Dowling, MI
There's something even more shocking about this post bud.
dustinwilt68
Wilt Built Work Saws
- Local time
- 8:38 PM
- User ID
- 1007
- Joined
- Mar 8, 2016
- Messages
- 5,933
- Reaction score
- 26,241
- Location
- Southwest PA
Do tell....
cuinrearview
Handy dood
- Local time
- 8:38 PM
- User ID
- 9248
- Joined
- Apr 16, 2019
- Messages
- 11,356
- Reaction score
- 78,962
- Location
- Dowling, MI
Your lineup that only includes one of those.
- Local time
- 8:38 PM
- User ID
- 2523
- Joined
- Jan 24, 2017
- Messages
- 4,960
- Reaction score
- 22,966
- Location
- Berkshire County, Massachusetts
I've been informed I have missed a couple 7910s lol please ignore my adhd and being too lazy to pan thru 166 pages!
dustinwilt68
Wilt Built Work Saws
- Local time
- 8:38 PM
- User ID
- 1007
- Joined
- Mar 8, 2016
- Messages
- 5,933
- Reaction score
- 26,241
- Location
- Southwest PA
I have had quite a few 572 here, currently have one on the lathe, had my own 572, swapped out for a 462. Nothing wrong any of them, just personal preference.
Cue the angry stihl fanboys....
See that is a tough call....
Looking at the peak power for sure.
If you look, close..... Limbing rpm/power, and low rpm grunt goes to the 500i that .2 peak hp is only part of the variable....
