What's on your bench?

[t4driller]

I still need to drill out the slots to fit all I want Mike.

I hear that. How you been? Finally cooled off a bit. I'm stilling planning on going to the gtg.

 

[Redfin]

I hear that. How you been? Finally cooled off a bit. I'm stilling planning on going to the gtg.

Doing well Mike. Yourself? Looks like Kris gtg is shaping up.

 

[t4driller]

Doing well Mike. Yourself? Looks like Kris gtg is shaping up.

Living the dream brother. Pounding them in 25 feet at a time. Lol. I need a vacation.

 

[Mastermind]

Baby saws.....

 

[mdavlee]

I just finished a 7900 for Miller. Got to get the 385 back up there and see how many more parts I need.

 

[NorthcentralYooper]

Finally getting time to finish my project 261 , waiting on a few small parts yet.

 

[TJ the Chainsaw Mechanic]

Right now I am working on a 94 Craftsman mower. Needs a lot of TLC. But should be a good runner.

 

[Chainsaw Jim]

Back at it with @RocketRoss57 's 2100cd. The intake and block are both freshly resurfaced flat with new gaskets. A thin wipe of loctite red on the surfaces and a drop of blue on the screws and this thing should hold tight.
Now it's time to set this cylinder in place and torque it down.

 

[Stihlbro]

Still messing with a Solo.

 

[Glock37]

Randy did the little elves get flywheel off overnight


Sent from my iPhone using Tapatalk

 

[Tor R]

Got cabers from the greek today, 242 and 346NE rings.


I got some work for tomorrow, at least I can finish the queen, the clumpy one has to wait for OE carb floor (its someplaces in my mess).
Both will go without gasket, and a few other things...one of the days I gotta figure out when Husky started to make those 242 XPG, it was between 90-91, maybe @SawTroll knows it.

 

[MustangMike]

Well, the parts I ordered for the MS 660 and MS 461 (pistons for both, etc) finally came in today, took almost 2 weeks!

Then the owner of these saws (a local tree guy) calls me and tells me that he is dropping off another MS 660 in the morning. seems that the local Stihl shop charged him $125 to rebuild the carb, and when it ran like crap afterwards, they just told him that "now it needs a new carb". He rented a crane and everything, put the big bar on the saw, and it just bogged in the cut.

I told him since the other 660 is currently apart, I'll just put that carb on it to see if it is the problem, but I may vac test it first.

 

[Deets066]

2100 on my bench, needs a few small things.

 

[Deets066]

Gas cap is leakin through the vent holes. What do you guys suppose would work good to plug em? JB?

 

[Sty57]

Gas cap is leakin through the vent holes. What do you guys suppose would work good to plug em? JB?

Some of the caps I've seen had a small duckbill in them.

What kinda saw is it for?

 

[Deets066]

Some of the caps I've seen had a small duckbill in them.

What kinda saw is it for?

Husky 2100

 

[Sty57]

Husky 2100

I never really paid attention to the older Husky caps.
I know the older Homelite & some of the Poulan ones had a small duckbill in them.
Most of the time they'll be gone and drip fuel out of them.

 

[Sty57]

I have used this one on a bunch of different saws.

 

[big t double]

I have used this one on a bunch of different saws.

What does it look like...the 1130 Stihls use a duckbill

 

[Sty57]

What does it look like...the 1130 Stihls use a duckbill

I'm not home and don't have a picture of the duckbill.
I can't remember who gave me that number for them. But my Husky dealer had them in stock.
So I'm guessing they fit a bunch of different things.