What's on your bench?

[jacktheripper]

What gear ratio is in your diffs?

4.10’s

 

[singinwoodwackr]

Axle swap.....

 

[Fleethirte]

It had the TTB Dana 50 setup

Thats quite an upgrade, i put a solid 44 in my 94 F150.

 

[singinwoodwackr]

Thats quite an upgrade, i put a solid 44 in my 94 F150.

2007 was the 'diff-drop' date Cut everything off with a plasma torch and start over. All custom stuff. Axle is made by Diamond in CO, 80-series Landcruiser hi-pinion front diff, ARB, Longfield 30s. We did start with a 3-link "kit" but wound up modifying all the brackets or just fabbing up completely different ones. Took, I think, 4 tac weld trys to get everything dialed in before burning.
3' of travel on each corner. Designed for the Rubicon and other norcal trails like Dusy and Red Mt. Maiden voyage on Rubicon didn't even require either locker
no place around here in ID to take it so am looking at selling.

 

[pbillyi69]

Axle swap.....
View attachment 487645View attachment 487647View attachment 487648View attachment 487649View attachment 487650

nice job

 

[singinwoodwackr]

nice job

It got upgraded and tweaked over the years. Found some weak spots that got beefed up, it is a very capable rock crawler…and wood hauler

 

[jacktheripper]

Thats quite an upgrade, i put a solid 44 in my 94 F150.

Pics?

 

[singinwoodwackr]

Thats quite an upgrade, i put a solid 44 in my 94 F150.

Leaf springs or radius arm?

 

[Fleethirte]

Leaf springs or radius arm?

I put the 78- 79 radius arms on. Ended up later down the road finding the james duff ones that i still need to put on eventually https://dufftuff.com/wp-content/upl...T0NbDt5TGiEUX3SMzaDgFivmW8z8cHm7scWZsVwT7NRBy

 

[singinwoodwackr]

I put the 78- 79 radius arms on. Ended up later down the road finding the james duff ones that i still need to put on eventually https://dufftuff.com/wp-content/upl...T0NbDt5TGiEUX3SMzaDgFivmW8z8cHm7scWZsVwT7NRBy

A friend of mine put an early Bronco radius arm setup on his 96 Tacoma…with coil overs. It is a one off, never duplicated. He kept the stock clamshell bushings. Everyone said it wouldn’t work…wrong.

 

[Fleethirte]

I cant find any pics of the front end lol she is currently keeping some slabs from bowing

 

[Reloaderguy]

 

[heimannm]

ICS

 

[Reloaderguy]

Husqvarna

 

[heimannm]

the chain

 

[heimannm]

Lancaster Model 400 with the bar mounted to the left.



Mark

 

[sawnami]

Trying to decide whether to do something with this or leave it as is.

 

[heimannm]

Do you have an IPL Steve? There is a snap ring under the seal that must come out before the crankcase will come apart.



It looks pretty good to me just the way it is.

Mark

 

[sawnami]

Do you have an IPL Steve? There is a snap ring under the seal that must come out before the crankcase will come apart.

View attachment 487788

It looks pretty good to me just the way it is.

Mark

That's important information to know. Mark. I do have an IPL but that's not to say that I would refer to it before I would struggle trying to take it apart.
So far everything looks very good on it and it runs on a prime shot. I have a Barker that is a twin to it other than it's yellow. Barker spared no expense to rebadge the saw after they got it from O&R. It has a sticker half the size of a postage stamp stuck in the center top of the saw and that's all the identification that's on it.

 

[heimannm]

Lancaster is going back together. We have spark...

The only photos I have today are the aftermath of the hail storm...



The north and west sides of my house and other buildings all took a pretty substantial hit.



Vinyl siding can be replaced.

Mark