What's on your bench?

[heimannm]

I continued on the unidentified Disston today, interesting fuel and pulse set up.





The fuel valve and fuel pump are located on the bottom of the fuel tank. The fuel valve is a slider that doubles as the stop switch.





Mark

 

[pbillyi69]

I continued on the unidentified Disston today, interesting fuel and pulse set up.

View attachment 487312

View attachment 487313

The fuel valve and fuel pump are located on the bottom of the fuel tank. The fuel valve is a slider that doubles as the stop switch.

View attachment 487314

View attachment 487315

Mark

that's quite the setup

 

[heimannm]

It is much simpler than the DO-101 I worked on last week.







I have a chain soaking, hopefully it will clean up O.K. and I can finish this one tomorrow. Has spark...fuel tank is crusty and the metering diaphragm is stiff so that will be it for now.

Mark

 

[hacskaroly]

It is much simpler than the DO-101 I worked on last week.

That saw cleaned up really nice!!

 

[EFSM]

It is much simpler than the DO-101 I worked on last week.

View attachment 487402

View attachment 487403

View attachment 487404

I have a chain soaking, hopefully it will clean up O.K. and I can finish this one tomorrow. Has spark...fuel tank is crusty and the metering diaphragm is stiff so that will be it for now.

Mark

That bar has an almost belligerent angle to it…

 

[heimannm]

Even with a loop of (well worn) 9/16" pitch chain it does not droop...



Mark

 

[Sloughfoot]

Thought I was going to get this one back together this afternoon.
Missing the oiler worm gear.

 

[pbillyi69]

i hate when that stuff happens to me

 

[Sloughfoot]

I didn't notice it was missing when I disassembled it. Wasn't really paying attention because it was oiling somehow.

 

[pbillyi69]

its not missing its on the floor. thats where mine waz... lol

 

[singinwoodwackr]

That bar has an almost belligerent angle to it…

Or…lol…

 

[singinwoodwackr]

i hate when that stuff happens to me

That’s when I go through my ‘random Stihl schtuff’ box and hope…

 

[pbillyi69]

me too diggin for gold at that point

 

[EFSM]

Or…lol…

Pull your mind out of the gutter…..
Lol
I was thinking of a rakish cap/hat angle

 

[Sloughfoot]

its not missing its on the floor. thats where mine waz... lol

I'm about 99% almost certain it was missing. It was oiling but just barely. It also didn't immediately reveal itself when I ordered another so it must've been missing.

 

[pbillyi69]

I'm about 99% almost certain it was missing. It was oiling but just barely. It also didn't immediately reveal itself when I ordered another so it must've been missing.

lol that's how you know for sure

 

[nv656]

Next project to start on, NOS 076 super and baby bro 041 super

 

[hacskaroly]

Next project to start on, NOS 076 super and baby bro 041 super

Good luck with the 076! I worked on an 075 and it wasn't until I was replacing the oil seals that I realized that someone did a mod and modded a 051 chassis to work with the 076 equipment. The 051 has two different sized oil seals and I couldn't figure out why the 075 oil seals would not fit, plus there are two different throttle linkages for the 075 and I needed the longer one which is NLA and nowhere to be found, all of the ones for sale are the shorter version. I ended up having to make a new one from a bicycle spoke. I also had to re-timesert the cylinder studs, they were all wiggly like a 6-year olds front teeth...what a pain that saw was!!

 

[singinwoodwackr]

Next project to start on, NOS 076 super and baby bro 041 super

Hey, that 041 actually looks used

 

[nv656]

Hey, that 041 actually looks used

I’ll try to make it look gently used when done