What's on your bench?

[hacskaroly]

You can tell which Ukranian carpenters are new arrivals by their track suit pants and members only jacket.

In Europe, they blend in, here they stick out like a sore thumb!!!

 

[59billy]

Best nursing hires here are Filipino. nail artists are Vietnamese, Ukranians are carpenters, Hmong are poachers.
Generally speaking. You can tell which Ukranian carpenters are new arrivals by their track suit pants and members only jacket.

So, a Ukrainian killed Tony Soprano?

 

[Sloughfoot]

So, a Ukrainian killed Tony Soprano?

Or a Russian disguised as a Ukranian playing a Russian.

 

[Kdrweld]

There must be a gene or something. I hired a general contractor to do some remodeling; one member of the crew was a Vietnamese guy who was probably the best finish carpenter ive ever seen. One of his coworkers offhandedly mentioned that he was also a nail artist. I guess attention to detail spans professions.

Yes, I sponsored the whole family and now all my brother in-laws are floor, finishing carpenters and they do stellar work

 

[Kdrweld]

But there’s only a few that understand reality whether it’s now or 1960, i’m pretty sure it was called. Make *s-word happen!!

 

[JKNW]

Shrinking an aftermarket 460 3/4 wrap for my 026. 3/4" out of the width, need to drop the top about an inch. Good TIG practice anyway.

 

[EFSM]

Echo 9010 blower crankcase. The fan side bearing is a good Japanese NTN but this is the second one I’ve seen with a failed cage. Both times the units were run without oil and it seems this is the first thing to fail, even before enough scoring takes place to lower the compression.

 

[Wilhelm]

In Europe, they blend in, here they stick out like a sore thumb!!!

In Croatia no one wears Adidas, nor top & bottom track suit sets.

PJ lookalike sweatpants with pulled up white socks apparently passes as manly.

 

[NZsaws]

So do you wear anything when you run the Dolmars?
You could cut the wrong log.

 

[bulletpruf]

AMC 360 cylinder heads. They were .003" warped. Used a granite surface plate and some 80 grit to surface them and now they're less than .0015" warped.

 

[Wilhelm]

So do you wear anything when you run the Dolmars?
You could cut the wrong log.

I'd consider myself lucky cuttin' "my own wood" whilst running my Dolmars!

Yeah, not going to happen.

 

[Fleethirte]

AMC 360 cylinder heads. They were .003" warped. Used a granite surface plate and some 80 grit to surface them and now they're less than .0015" warped.

View attachment 478479

Will the head gasket make up the difference?

 

[EFSM]

One of the dirtier saws I’ve seen recently. The stuff was caked on so hard that a pressure washer wouldn’t take all of it off.

 

[EFSM]

Will the head gasket make up the difference?

What difference? .0015 ain’t much….
Any type of gasket should have that much crush.

 

[bulletpruf]

Will the head gasket make up the difference?

The spec is .001” per cylinder so a v8 head needs to be warped less than .004”. In other words it was within spec before I started but not great. now it’s less than .0015 so that’s quite good.

 

[bulletpruf]

What difference? .0015 ain’t much….
Any type of gasket should have that much crush.

Bingo.

 

[jacktheripper]

The 450 is starting to look a lot nicer. I have been repeatedly washing and scrubbing it to get the caked on crap off. It’s probably the most deeply dirty saw that I’ve ever dealt with.

 

[jacktheripper]

The other Jonsereds 910e is also cleaning up nicely. Replaced a rear AV bushing and rear handle assembly. This is going to get new fuel tank vent, impulse line, fuel line and filter, and carb kit.

 

[hacskaroly]

The 450 is starting to look a lot nicer. I have been repeatedly washing and scrubbing it to get the caked on crap off. It’s probably the most deeply dirty saw that I’ve ever dealt with.

That is sounding really good!!

 

[singinwoodwackr]

Shrinking an aftermarket 460 3/4 wrap for my 026. 3/4" out of the width, need to drop the top about an inch. Good TIG practice anyway.

View attachment 478463

What will you use to re-wrap it?