What's on your bench?

[oddsawz]

Follow up. Strong and smooth

 

[heimannm]

 

[JKNW]

The 647G got OFF the bench, because it's too dang loud to run inside the shop. Was having trouble starting, thought the little check valve in the fuel inlet was bad since it was pushing pressure out the fuel cap... Turns out you just gotta put the carb together right the first time so that it can open the needle! Gave the chain a tune up and we'll get it in the wood this weekend hopefully. Definitely still loaded up on whatever oil the last guy had in it, she's a smoker.

 

[Shane¹]

Custom modified bar plate for the 9000 hybrid using 123 bar plate euro front studs and a Stihl bar with Stihl bar studs

 

[Agent Smith]

Machined the case halves of some 100cc kids quad for a buddy of mine. His son races them things and he's building a new motor for him with a stroker crank.

 

[Bigmac]

Got the MS 250 back together, but it was missing the clutch drum, gonna have to wait till Monday to get one at the local dealer. Revisited the MS 270, have it running well and now need to revisit the 0 34 super.
Not sure how crazy I wanna go with this 064, but I end up getting an NOS tank. Saw runs well, made some cuts yesterday with it.

 

[LAWN BOY]

The 026 was on the bench for adjusting the carb and to sharpen the chain. There's a raker missing. I got proper hardware to mount the dogs on it. I installed a new fuel line and filter on the pm5700 after cleaning the very dirty gas tank. I also installed a new used yellow recoil and new mounting bolts. It runs! The gas cap should be here within the next couple days and then I can get it in some wood. Didn't test the oiler yet.

 

[ZeroJunk]

My shop this morning. Bunch of junk. Case 444 clutch needs to be rebuilt.

 

[Sloughfoot]

Long over due 044 oil line replacement and Honda brush cutter carb change on my back porch bench.

 

[av8or3]

Hadn’t seen one of these before. Factory plug instead of limiter in Tillotson HS carbs.

 

[stretch5881]

My shop this morning. Bunch of junk. Case 444 clutch needs to be rebuilt.


View attachment 456016

Wouldn't you like to slap the person that came up with the name "E-Z adjust clutch"?

 

[Squareground3691]

Sum V - Stack action,

 

[heimannm]

Stihl 030 from the Lehman donation.



Filthy pig.



Had been chipped, did have spark.



All cleaned up now.



Mark

 

[JKNW]

At long last, a fully assembled, running Sears lightweight. Need to grab a couple bar nuts the next time I'm out and about but other than that she's ready to hit the woods.


Wasn't without a little drama though. I knew better than to stray from rope to tighten that clutch but I did it anyway and got to go fishing.

 

[hacskaroly]

That is a nice looking saw...bummer about the piston stop. I have one of those, but never seem to get it to work right, but rope on the other hand works every time!!

 

[whitesnake]

My shop this morning. Bunch of junk. Case 444 clutch needs to be rebuilt.


View attachment 456016

Looks fun. Reminds me I really need to get my zero turn up to snuff the grass will be growing before I know it.

 

[old 040]

Stihl 030 from the Lehman donation.

View attachment 456146

Filthy pig.

View attachment 456147

Had been chipped, did have spark.

View attachment 456149

All cleaned up now.

View attachment 456148

Mark

The 030av was the first saw I bought where I paid good money for back in the early 80's. I still own a nice one.
If you plan to make that one a runner, confirm that the flywheel is from an 031ave (electronic ignition) if you plan to re-use that chip.
These saws will run with a chip, but will be out of time and run sluggish if using a points flywheel. A pic of the one I own now.