What's on your bench?

[Woodwackr]

See, the key is using Similac containers...without those, the entire system would be hosed and there would be parts everywhere. Can't use Tupperware or yogurt containers...has to be Similac containers....

What would happen if he used Dissimilac?

 

[hacskaroly]

What would happen if he used Dissimilac?

I am sure dissimilar results would ensue...

 

[Woodwackr]

I am sure dissimilar results would ensue...

Ensue or is he old enough for Ensure?

 

[Mastermind]

Y'all are complicating this. LOL

 

[hacskaroly]

Ensue or is he old enough for Ensure?

Depends....

 

[LAWN BOY]

Husqvarna 142, runs fine, need minor carb adjustment and or cleaning, not oiling, some oil on saw as you can see, I did a quick bar cleaning job, any ideas?

 

[Mastermind]

Start it without the bar. See if you get oil at the bar pad.

 

[Tor R]

It's been a few years since I had a project in this thread,

soon, but need a couple of thorough washes!

 

[Tor R]

My 238 parts saw is getting interesting, this was on the edge down to the crankcase, perfectly positioned to not fall down, it is less a part for the piston that has disappeared. What is missing has been chewed up.

 

[bigbadbob]

from a very tired husky 61. have never seen this B4

 

[heimannm]

Just about used it up...

Mark

 

[nbbt]

Picked up this non-running Lawnboy, with a suspected bad coil.

Started by giving the mower a bit of a cleanup as it was rather dirty oil soaked.
Replaced the coil with a used one that was saved from a piston/cylinder scored mower.


After reassembly it started on the 3rd pull. Noticed right away that it was spitting dirty oil spots from the lower crank seal area..
Found that someone had previously replaced the seal with the wrong style and it had ejected itself.
Had the right dual lipped one with the steel outer case in my spare parts supply and did the swap.

While the muffler cover was off to get to the seal for replacement, cleaned the exhaust ports . One was about 20% carboned and the other two had smaller amounts.
Back to seeming to be a great running mower.

I like this series partly because it has a metal carb that has an external fuel adjustment needle screw.

 

[farminkarman]

Here is my Echo 490 I donated for the raffle at @Stump Shot ‘s GTG. This is headed to @LAWN BOY compliments of @bradb123. I ended up cutting the base, raising the exhaust and transfers. I did a simple muffler mod and removed the limiters from the carb. Since I had an extra K095 bar, I modded it to fit and will be sending it along as well.

 

[LAWN BOY]

View attachment 438506View attachment 438507View attachment 438508View attachment 438509Here is my Echo 490 I donated for the raffle at @Stump Shot ‘s GTG. This is headed to @LAWN BOY compliments of @bradb123. I ended up cutting the base, raising the exhaust and transfers. I did a simple muffler mod and removed the limiters from the carb. Since I had an extra K095 bar, I modded it to fit and will be sending it along as well.

Nice. Looking forward to it. Thanks again guys.

 

[Mastermind]

Very nice.

 

[Stump Shot]

View attachment 438506View attachment 438507View attachment 438508View attachment 438509Here is my Echo 490 I donated for the raffle at @Stump Shot ‘s GTG. This is headed to @LAWN BOY compliments of @bradb123. I ended up cutting the base, raising the exhaust and transfers. I did a simple muffler mod and removed the limiters from the carb. Since I had an extra K095 bar, I modded it to fit and will be sending it along as well.

Excellent!

 

[Squareground3691]

project p51, fresh bar chain and stainless spikes

Great saw ,

 

[Squareground3691]

Big girl , BP 655 going West Coast style air ,

 

[Woodwackr]

Been so long since I assembled one of these I had to look stuff up, lol
Heading to NC

 

[nv656]

Great saw ,View attachment 438881

Shoot. Almost loook like twins! Tho you beat it with that roller nose bar. Do you have anymore?