What's on your bench?

[Wilhelm]

Dolmar PS-6100CE getting a chain sharpening and basic maintenance.
Dolmar 099 full chisel, round ground.

 

[Wilhelm]

Dolmar PS-6100MMWS getting chain round ground and basic maintenance.
Modified full chisel Dolmar 496 (Oregon Vanguard).

 

[Hinerman]

562XP MKII View attachment 434866View attachment 434867View attachment 434868View attachment 434869

Let me get this straight. It is designed to crimp the fuel line, correct?

 

[Mastermind]

Let me get this straight. It is designed to crimp the fuel line, correct?

Negative. That's the primer bulb circuit. And that line was in the wrong place.

 

[Wilhelm]

Dolmar PS-550, chain ground and basic maintenance.
Husqvarna full chisel X-Cut chain.

 

[Wilhelm]

Dolmar PS-7300, chain grinding and basic maintenance.
Was 24" Oregon full chisel full skip.


But I set her up with my 36" B&C, Iggesund Forest solid steel milled bar & Carlton full chisel "hillbilly skip" chain - and the CSM.

 

[Wilhelm]

Dolmar PS-7310, off with the .404", pair back up with the 3/8" 24".

 

[JIMG]

New piston for the Mac 800.
For some reason the NOS crank arm was out of spec for the big end needle bearings.

 

[Woodwackr]

2 500is today. "Won't start".
First was easy...impacted and seized clutch, needle, crank shaft. Used a gear puller to get it apart, cleaned all...back together, fired right up.
The second...scored...both sides...straight gassed.
This one will be a while

 

[Woodwackr]

May as well open up the exhaust port and muffler...
Won't know if the cyl is OK till tomorrow.

 

[Mastermind]

 

[Woodwackr]

View attachment 436475

Ok, so…start a raffle…name those cylinders
Winner gets a cookie.

 

[maulhead]

Ok, so…start a raffle…name those cylinders
Winner gets a cookie.

 

[Mastermind]

Ok, so…start a raffle…name those cylinders
Winner gets a cookie.

6 MSs, and an XP.

Gimme my cookie.

 

[Shane¹]

6 MSs, and an XP.

Gimme my cookie.

As long as you remember which one goes to what saw it's a good day lol

 

[Mastermind]

As long as you remember which one goes to what saw it's a good day lol

We have a pretty good system. We take a saw out of the box it was shipped in, then use that box for the parts. The small parts go into a Similac container with the customer's name on it. The saw itself is labeled with the customer's name as well. Each cylinder is numbered, and that number is also written on the tag that is on the saw.

 

[Shane¹]

We have a pretty good system. We take a saw out of the box it was shipped in, then use that box for the parts. The small parts go into a Similac container with the customer's name on it. The saw itself is labeled with the customer's name as well. Each cylinder is numbered, and that number is also written on the tag that is on the saw.

Sounds like a good system

 

[Fleethirte]

Sounds like a good system

thats why he is the mastermind!!

 

[hacskaroly]

The small parts go into a Similac container with the customer's name on it.

See, the key is using Similac containers...without those, the entire system would be hosed and there would be parts everywhere. Can't use Tupperware or yogurt containers...has to be Similac containers....

 

[Mastermind]

See, the key is using Similac containers...without those, the entire system would be hosed and there would be parts everywhere. Can't use Tupperware or yogurt containers...has to be Similac containers....

Luckily, a good friend sent me a large box full of Similac containers.