What's on your bench?

[Czed]

Complaint was high idle

Red armor 40/1 will fix that

 

[gurwald]

I'll get a 12mm scrench for when I turn 50.

13mm socket is standard on M8 bolts.

 

[Bigmac]

I'll get a 12mm scrench for when I turn 50.

13mm socket is standard on M8 bolts.

It’s standard for general fasteners, but lots of factory suppled fasteners are 12mm, all Japanese fasteners are 12mm for dirt bikes a quads

 

[Moparmyway]

It seems that I’ve got a few aftermarket 12mm nuts on some of my Husky saws, all of the ones I purchased new are 13mm .......... OEM Husky nuts ordered.




I grew up with dirt bikes, still have them around, I guess it just seemed normal to me .........

 

[Wolverine]

Might be the worse I’ve ever had on my bench. My cousin gave me the saw. 18 years use.

 

[tickbitintn]

Might be the worse I’ve ever had on my bench. My cousin gave me the saw. 18 years use.
View attachment 241645
View attachment 241646
View attachment 241647

Meh, that'll buff out. [emoji846]

Lol

Sent from my XT1635-01 using Tapatalk

 

[tickbitintn]

Outside looks pretty clean.

Sent from my XT1635-01 using Tapatalk

 

[JoeDirt]

Top ends are cheep. Just did a 55 Rancher.

 

[Wolverine]

Top ends are cheep. Just did a 55 Rancher.
View attachment 241700 View attachment 241701 View attachment 241703

OEM? What did you pay?

 

[JoeDirt]

OEM? What did you pay?

Yep, I used an OEM kit. I got mine from a local dealer but I think they were right around $60 on eBay. Deleted the base gasket and opened the muffler up just a hair and it runs really good for what it is.

 

[JoeDirt]

That 55 was the first saw I really tore into. @PA Dan walked me through it to make sure I didn't do anything stupid. I probably only have 2 or 3 tanks through it, but its a nice saw, I really like it. It pulls an 18" bar through Oak no problem.

 

[tickbitintn]

I bought an AM closed port one a couple years ago... It was more than the OEM ones are now. [emoji52]

Sent from my XT1635-01 using Tapatalk

 

[a. palmer jr.]

Okay, got one of the Homelites running..problem is it oils too much. The duckbill valve is one that you slide into the end of the pulse hose and nowhere to put the little iron piece that relieves the pressure into the tank so I took the smallest drill bit I could find and drilled a hole into the oil cap thus relieving some of the tank pressure, hope it works..I can always fill the hole back up if it doesn't..

 

[a. palmer jr.]

Meh, that'll buff out. [emoji846]

Lol

Sent from my XT1635-01 using Tapatalk

Maybe a belt sander...

 

[Backtroller]

I bought a MS260 with a Walbro WT605 on it??? The numbers stamped on it are actually “wte 605”. Anyone have any idea what it is off if? Here it is compared to a WT194. The 194 does not have the snorkel on it

previous owner said it didn’t run right

 

[Backtroller]

Has an extra hole

 

[Saw_Squatch]

Got an old craftsman and an old poulan (so technically two old poulans) both appeared to have sat in a vat of ethanol for 10-20 years each. After breathing incorrectly on and effectively disintegrating the talcum powder fuel lines, I believe I diagnosed their starting problem. Amazingly after draining the decade old fuel, replacing the lines, filling up with some E0 and Echo Red Armor, and 20-30 pulls a piece they're both now running cutting again with no apparent damage to the carburetor.

 

[JohnnyBlade]

359 update. Going together and decided to share a lil mod. Used a 350 dog for the bracket. (The cut up one and stock to show what was done. Sorry i threw a piece away but u get the jist.)
372 dog with roller catcher was installed on the 359. Had to do some modding to that dog as well. Bottom hole was oblonged and relief cut for the bottom of case. Top hole was slotted. Bracket was made as an extra strengthener prob overkill but wanted to share.
Also makes the Hooskie kickstand most importantly
And with the extra width thre is still ton of thread on bolts.

 

[HYPERSAWS]

O46

It will be a complete restore it was my boss/friend Frank Neely saw who pass away last year

 

[PA Dan]

359 update. Going together and decided to share a lil mod. Used a 350 dog for the bracket. (The cut up one and stock to show what was done. Sorry i threw a piece away but u get the jist.)
372 dog with roller catcher was installed on the 359. Had to do some modding to that dog as well. Bottom hole was oblonged and relief cut for the bottom of case. Top hole was slotted. Bracket was made as an extra strengthener prob overkill but wanted to share.
Also makes the Hooskie kickstand most importantly
And with the extra width thre is still ton of thread on bolts.View attachment 241843View attachment 241844View attachment 241846View attachment 241847 View attachment 241849

Did you run it yet?