What's on your bench?

[WillG]

Quickly hand filed the chain on the 031. I saved it!

Sent from my E6910 using Tapatalk

 

[Tor R]

Tor do tell! This is very interesting! View attachment 222431

aint difficult to get the shine, probleby 10 minute job. Credit goes to @rattler, the guy is a clever guy, that I can say.
WD40, 240 grit, 600 grit, if I got lots of time 1000 grit and a round 2000 grit, most of the time I skip the last two.
3-5 minute with alu polish stuff, and thats it.

 

[Spladle160]

Just finished rebuilding this last night. Kind of cool. It's a k45ss from before Hobart sold KitchenAid in 86. Came from the dumpster just needed a new speed controller but got a full pull down, clean and grease. Oh, and purple ghost skull flames cause uh... yeah.

 

[JohnnyBlade]

aint difficult to get the shine, probleby 10 minute job. Credit goes to @rattler, the guy is a clever guy, that I can say.
WD40, 240 grit, 600 grit, if I got lots of time 1000 grit and a round 2000 grit, most of the time I skip the last two.
3-5 minute with alu polish stuff, and thats it.

Very nice! I see u have a exhaust relief or step but its on the roof? Ive seen and done them on the floor. Any benefits to doing it on the roof?

 

[huskihl]

Just finished rebuilding this last night. Kind of cool. It's a k45ss from before Hobart sold KitchenAid in 86. View attachment 222624 Came from the dumpster just needed a new speed controller but got a full pull down, clean and grease. Oh, and purple ghost skull flames cause uh... yeah.

Husqvarna...

Chainsaws
Sewing Machines
Kitchen Mixers

 

[WillG]

Just touched up the 034. I'll have to wait till tomorrow to make a couple of cuts since I can't run anything after 9 pm.

Sent from my E6910 using Tapatalk

 

[JohnnyBlade]

Husqvarna...

Chainsaws
Sewing Machines
Kitchen Mixers

There is a sewing shop by me that has a husqvarna sign. Ill take a pic next time im over there

 

[wcorey]

Husqvarna...

Chainsaws
Sewing Machines
Kitchen Mixers

They made awesome cast iron stoves.

I've put this one up somewhere here before...

 

[huskihl]

They made awesome cast iron stoves.

I've put this one up somewhere here before...

View attachment 222673

View attachment 222674

Nice.
I forgot about motorcycles too

 

[MustangMike]

Bill, that is sharp!

 

[wcorey]

Nice.
I forgot about motorcycles too

And guns... Their emblem with the H actually depicts a gun sight. IIRC that's their original business going way back.

I also have a husqvarna/viking sewing mach and of course a dirtbike, '87 wr430, last year before the Cagiva buyout.
None of their guns unfortunately, always wanted one of their .22 target pistols.

 

[shadco]

Nice.
I forgot about motorcycles too

Back in the day.



.

 

[StuntCockWelder]

Back in the day.

View attachment 222709

.

 

[StuntCockWelder]

Back in the day.

View attachment 222709

.

View attachment 222740

 

[Tor R]

Very nice! I see u have a exhaust relief or step but its on the roof? Ive seen and done them on the floor. Any benefits to doing it on the roof?

its how Husqvarna does the roof, the theory is to reduce the carbon buildup, kinda get a exhaust gas swirl. If my memory is correct they had none steps in the early models, a tad in medium model top end, and made the step bigger in the latest models.

 

[Stevetheboatguy]

Back in the day.

View attachment 222709

.

View attachment 222740

My ol ride. A good friend has it now. Maybe I'll own it again one day.

Damn near killed me a few times. Kinda miss it. Was a handful. Hit the sweet spot and that front end was coming up. Felt more like a two stroke than a four. 112 gets expensive fast.


Steven

 

[WillG]

Tested my filing job out on the 034. Used a 7/32 file at 30 degrees on the Stihl RM chain. 4 strokes each cutter. I guess I did good. Also finally got the idle speed and mix set for when she's at operating temperature.

Sent from my E6910 using Tapatalk

 

[Huskygasaxe]

Been a while. Hello all. 394xp. I have a 394 cylinder on it ported by walkers from Vancouver island, muffler was gutter and modded by them as well. I had a new top cover but it doesn’t match the colour and with the muffler mod I would have to cut it. No thanks.

 

[heimannm]

Someone dropped off an XL12 a few weeks ago. I did not take a B4 photo but is was a rusty, filthy, dust and oil encrusted mess so I tore it down to give it a good cleaning.



Back together, somewhere along the way I lost the choke knob & choke rod. When I put the AF cover on the knob crumbled into pieces but I should have a spare in the attic of the new shop amongst the saws I brought home last fall.





I moved all my chain and chains to the new shop so I'll put one on when I get it over there.

Mark

 

[WillG]

Assembled my new log horse to do some bucking for my dad tomorrow. A little bit of a pain in the butt to figure out how the braces went however once I figured that out it went right together. Tunes helped of course.

Sent from my E6910 using Tapatalk