What's on your bench?

[WillG]

024 just left not too long ago. Still have 031 and 015 to part with. I've had my fun with them.

Sent from my E6910 using Tapatalk

 

[beaglebriar]

LOL. Yes. [emoji23]

Actually lost 1" compared to the stock dawg.

 

[RI Chevy]

1 inch is 1 inch. Lol

 

[Wood Chopper]

Dolmar 5100 trying to remember how all this crap fits back in this saw...[emoji13]

May not help lol

Sent from my iPhone using Tapatalk

 

[WillG]

Dad's buddy's Jonsered 630 Super. Installed a new dawg and replaced missing cover hardware.

Sent from my E6910 using Tapatalk

 

[PA Dan]

May not help lol

Sent from my iPhone using Tapatalk

I got some pics earlier this afternoon and got it together! Thanks buddy!

 

[justoldsaws]

395xp, needs new crank, bearings, seals, cylinder and piston.

 

[redlight066]

Finished this up today. Put a new hose on the top handle as a surprise. I’ve got it down to 5 minutes and no cussing. Lol

 

[markds2]

A tidy 2015 model 395. Big end had gone for some reason and had taken out the piston. Cylinder was still good. Picked it up for approx $300 and with a good secondhand crank, new mains and seals and a Meteor it's nearly ready to go. Just need to cut an extra hole in the muffler and install a 288 deflector using nutserts.

 

[WillG]

Clean up and touch up on my 2 regular users. Scored a trailer load of free white cedar, ash and oak from a buddy who is moving. Unloading the trailer after work tomorrow and this weekend I'm getting the rest of the wood from him along with some pine from a vacant house...

Sent from my E6910 using Tapatalk

 

[Redfin]

 

[RI Chevy]

Love it

 

[WillG]

A dinosaur! 051AVE. Was looking for why the last time I used it it lost power and wouldn't idle. Found loose intake block! So luckily with a couple of new gaskets and a carb kit she'll be roaring again!

Sent from my E6910 using Tapatalk

 

[markds2]

A dinosaur! 051AVE. Was looking for why the last time I used it it lost power and wouldn't idle. Found loose intake block! So luckily with a couple of new gaskets and a carb kit she'll be roaring again!

Sent from my E6910 using Tapatalk

Talking about 1111 series dinosaurs with loose stuff I just had one worse. This is an 076, I'm very surprised it had got this far. The cylinder gasket is completely disintegrated and the cylinder has worn an impression in the crankcase! The following pic shows how the cylinder studs were when I dismantled it. Interesting thing is the KS cylinder and piston is still in perfect condition!

 

[WillG]

Talking about 1111 series dinosaurs with loose stuff I just had one worse. This is an 076, I'm very surprised it had got this far. The cylinder gasket is completely disintegrated and the cylinder has worn an impression in the crankcase! The following pic shows how the cylinder studs were when I dismantled it. Interesting thing is the KS cylinder and piston is still in perfect condition!
View attachment 222002

Oh wow that's bad! Just ordered a carb kit that comes with all new intake gaskets etc.

Sent from my E6910 using Tapatalk

 

[WillG]

Weedeater hedge trimmer that is getting a carb kit. After work today I also unloaded my trailer, marked the wood that's going to my dad at 15". Setup my sound system for tunes while unloading. Getting another load tomorrow and will cut everything up this weekend. Made a loop of starter rope for hanging my Spencer tape on my belt loop.

Sent from my E6910 using Tapatalk

 

[justoldsaws]

Well that was fun, no room for error, bolt was broken off clean with the case
Bolt for felling spike on 395xp.

 

[WillG]

All back together, running and adjusted! High speed was too lean and the low speed was too rich. Idle is around 2400 and wot is right around 10000. Sounds good. I'll recommend that he uses TruFuel since he doesn't use it much and the metering diaphragm reflected that as it was as stiff as a board.

Sent from my E6910 using Tapatalk

 

[sonoransaw]

My brother and I put together this homemade right angle porting tool (we po' folk).... The bit goes on top, the bottom shaft connects to your dremel (the tape there just keeps the bearing race in as it was a little looser than the top one). The bit is held in place by a set screw (protruding length can be adjusted). There is an o-ring down inside the body that turns things....My brother has a metal lathe and turned the mini internal pulley parts.... Initial testing is promising... What do you guys think? (The bit in it was just for testing. I'm going to order some proper carbide bits.)

 

[Graf]

From Lapeer Michigan a new Walbro wt55 for this troublemaker, an italian made Mcculloch pm484