What's on your bench?

[Glock37]

12 mm 044, is she stock? Very nice condition.

Yes all stock Some new some powdered parts cyl is a very nice slant fin hd 8 carb


Sent from my iPhone using Tapatalk

 

[MustangMike]

Nice!

 

[Backtroller]

 

[huskihl]

View attachment 147167 View attachment 147168

Rabbit hole......

 

[Drptrch]

Coffee and Citronella [emoji13]


Erik

 

[Backtroller]

Amazying how small a 026 actually is

 

[Mkinslow]

How about a bench remodel. Don't have any saws at the moment of mine or customers, which is kinda sad.

Sent from my SM-G892A using Tapatalk

 

[usmcbuckwild]

How about a bench remodel. Don't have any saws at the moment of mine or customers, which is kinda sad.

Sent from my SM-G892A using Tapatalk

I like the drill holder set up.

 

[MustangMike]

I have to re do the whole garage soon to get the stang back in before the snow. Saws all over the place! Made storage for 10 and have over 20!

 

[MG porting]

How about a bench remodel. Don't have any saws at the moment of mine or customers, which is kinda sad.

Sent from my SM-G892A using Tapatalk

Yea i think it would be a good time to clean up the mess that the tornado left. Lol

 

[NWWrench]

Here is a early 10mm44 that I spit and rebuilt for my Vietnam Veteran dad . I built this saw for him for Veterans day a few years ago. Thanks to all active and retired Veterans , I could be more proud to be surrounded by such good people,
Anyways, my dad just turned 70 and loves the saw but has a hard time starting I cant remember if I plugged the decomp or if it was early enough it did not have one. It rips in stock form so I may swap cylinders for him. Don't have it on the bench yet but he will be dropping it off soon.

 

[MG porting]

Here is a early 10mm44 that I spit and rebuilt for my Vietnam Veteran dad . I built this saw for him for Veterans day a few years ago. Thanks to all active and retired Veterans , I could be more proud to be surrounded by such good people,
Anyways, my dad just turned 70 and loves the saw but has a hard time starting I cant remember if I plugged the decomp or if it was early enough it did not have one. It rips in stock form so I may swap cylinders for him. Don't have it on the bench yet but he will be dropping it off soon.View attachment 147262 View attachment 147263

I'd be careful you're going to have to check and make sure that the rings are in the right location for the decomp cylinder or oops.

 

[MG porting]

Well this saw is a nice one runs strong but haha oil pump is froze up solid. To bad he needs it for tomorrow he's not going to be happy oh well I can't invent a new one. Lol

 

[Mkinslow]

I like the drill holder set up.

Thanks I've been seeing videos of them and decided to build one. Its a lot better than I thought it would be. Of course I've gotta find time now to get everything organized lol.

Sent from my SM-G892A using Tapatalk

 

[Mkinslow]

Yea i think it would be a good time to clean up the mess that the tornado left. Lol

Lol. I agree bud

Sent from my SM-G892A using Tapatalk

 

[longleaf]

I figured out sometimes the best way to get into a hard to reach spot is to watch YouTube and see how someone else figured out how to reach it.

 

[kingOFgEEEks]

McCullough 1-46. No spark. I cleaned and set the points. Thinking the condenser might be borked? Are these a good candidate for the Nova chip conversion?

 

[MG porting]

McCullough 1-46. No spark. I cleaned and set the points. Thinking the condenser might be borked? Are these a good candidate for the Nova chip conversion?

As long as the coil is good I don't see why not.

 

[Drptrch]

Wish this was !!




Erik

 

[tickbitintn]

Wish this was !!




Erik

Dang that's cool

Sent from my XT1635-01 using Tapatalk