What's on your bench?

[MustangMike]

Al, is that about where the squish and compression is on mine?

You guys are going to like these saws!

 

[Dub11]

This doesn't fit on my bench.......

View attachment 56796

Then get a bigger bench lol.

 

[Dieselshawn]

Dub11: a bigger bench it is....

There can never be a bench too big eh?

 

[Mattyo]

Bigger bench? That thing doesn't hardly fit on the trailer.....wow

 

[Dieselshawn]

Mattyo: yes, it's a long car. Not the biggest out there though. I think that's Cadillac?

Biggest vehicle I've had on that trailer was a 1 ton extended cab long box 4x4 Dodge Ram Cummins.

Trailer was pressed down like a bow under the weight as the tires of the truck rested at the very front and the rear was at the edge at the back. Was only a short 10 min trip from shop to my place so trailer is still in one piece.

 

[Dub11]

Dub11: a bigger bench it is....

There can never be a bench too big eh?

Make sure its in the twin post 12k flavor

 

[Dieselshawn]

Dub11: I would love to have a 2 post 12,000 hoist... need one badly. That means my garage must be emptied of clutter, snowmobiles, parts etc.

 

[Dub11]

Dub11: I would love to have a 2 post 12,000 hoist... need one badly. That means my garage must be emptied of clutter, snowmobiles, parts etc.

Me too I have two foot paths in my shop now I think it would be faster to just poor a pad and leave it outside thats what my uncle did.

 

[Dieselshawn]

Dub11: same here, 2 foot paths through the shop and a large area occupied by a large Dodge Ram truck.

 

[drf256]

Al, is that about where the squish and compression is on mine?

You guys are going to like these saws!

I'd have to check my notes Mike.

I usually get the squish between 18 and 22, but that's with .026 solder. So likely .017-.021.

I don't think I've gotten one at less than 225 psi the way I do them. I remember yours being non-decomp Mike.

Can you check it now that's it's broken in?

 

[Czed]

Here's something handy for me maybe some of you guys i like to work out side when it's nice i have a 4×16 4ft tall bench lol and often i'm asked to go to someone's home to look at saws atvs dirtbikes etc. I made this up years ago i carry different size echo line some plugs common carbs and kits and adjustment tools also hemostats everything for a common repair and motoseal lol it saves me time looking for tools.

 

[Definitive Dave]

Here's something handy for me maybe some of you guys i like to work out side when it's nice i have a 4×16 4ft tall bench lol and often i'm asked to go to someone's home to look at saws atvs dirtbikes etc. I made this up years ago i carry different size echo line some plugs common carbs and kits and adjustment tools also hemostats everything for a common repair and motoseal lol it saves me time looking for tools.View attachment 56830

Hey that's my toolbox man how did you get that out of my garage ?

 

[Czed]

Hey that's my toolbox man how did you get that out of my garage ?

Wasn't easy lol
Hey do you have oem 372 wrist pin bearings i searchedd

 

[MustangMike]

Al, you are correct, mine does not have a decomp valve. I don't have a compression gauge, but I can tell you it is stout!

It also cuts way disproportionate to it's size!

 

[t4driller]

Finished grinding on my 460 cylinder for my hybrid.

just have a little more polishing to do on exhaust port.

 

[Onan18]

Breaks and Scatters

 

[USMC615]

Does re-lining about 15-20 spinning rods this afternoon count for anything? I know the cold/winter ain't over with by no means (crazy weather, 75 degs here in mid-Ga this afternoon)...but I'm getting rigged and ready. It's gonna get hot and heavy on the crappie and bream for too long. Re-lined all my baitcasters/bass gear last week. I'm ready to snatch lips, fill live wells and coolers. Ya feel me??

 

[RocketRoss57]

AM circlip lesson learned. 390 top on 290.

 

[decableguy2000]

AM circlip lesson learned. 390 top on 290.View attachment 56884View attachment 56885

That buff out

 

[Canadian farm boy]

Don't know how I feel about this one yet. MS270. It needs a little love. Lol