What's on your bench?

[drf256]

Good for you Al I got to make some plates too.

Sent from my XT1060 using Tapatalk

Snapped a tap off in the plate.

Was an hour of tig welding and cursing to get it out. Last hole of course.

 

[rattler]

Snapped a tap off in the plate.

Was an hour of tig welding and cursing to get it out. Last hole of course.

Your luck is like mine Al.

Sent from my XT1060 using Tapatalk

 

[Cut4fun]

Dropped off, took it apart, got lucky and had all the parts it needed on hand. Picked up today.

 

[paragonbuilder]

Gearing up to finally use lathe for bands

View attachment 32251

Nice Doc! Same lathe?


Sent from my iPhone using Tapatalk

 

[Cut4fun]

Whats on the Floor.

My new to me 2cc I picked up today while out goofing off this morning.

Going to hang it up in the barn shop somewhere with the other ones.

 

[rattler]

Whats on the Floor.

My new to me 2cc I picked up today while out goofing off this morning.

Going to hang it up in the barn shop somewhere with the other ones.

View attachment 32261

Nice!

Sent from my XT1060 using Tapatalk

 

[drf256]

Nice Doc! Same lathe?


Sent from my iPhone using Tapatalk

Nope

 

[paragonbuilder]

Nope

Sweet! What did you get?


Sent from my iPhone using Tapatalk

 

[psuiewalsh]

He switched to 40:1 after he fried this saw, as I said he previously told me, this saw was running 50:1 when it quit.

Check the intake boot closely. They like to get small tears when they flex the tank they leak but are fine stationary.

 

[Cut4fun]

Whats OVER your bench . Moved the old one down about 20 feet and put the nicer one over bench #2.

Old one no handles 1st pic.

New one 2nd pic.

 

[Redfin]

502 50 66-02 is for the big ones, 18mm, like 288 size

502 51 00-02 is 14mm for the larger 272 size ones

502 50 67-01 is 11mm for the smaller ones

Thanks man. Needle nose pliers have been my go to.

 

[panteliss]

http://m.ebay.com/itm/502510002-AV-DAMPER-REMOVAL-TOOL-HUSQVARNA-CHAINSAW-/150564962849?nav=SEARCH

Ouch! Smiling Randy strikes again.

What Ouch?? you see the picture ? take your angle grinder a piece of 5mm thick metal plate and produce the tool one 11 one 14 and one 18 mm
so simple

 

[Redfin]

I used colored wires from phone co. cable.
BBB

Blue, orange, green, brown and slate.

 

[panteliss]

i ordered a clutch tool for a husky i was working on took him 5 days to send out and im just the next state over i messaged him asking why it wasnt sent out and he said he had a week to send out and wouldnt change that

sent me adress if you want husqvarna tools with distributors prices , not with a f@cking bay prices

i pay 25 euros for the above tools ( three of them 11,14,18 mm ) theese for the rubber mounts

 

[Stump Shot]

@exSW, Here's a place for Husqvarna tools. http://www.choochooparts.com/body_g3.asp?CAT3=79120&CAT2=79000&CAT1=70000

 

[exSW]

@exSW, Here's a place for Husqvarna tools. http://www.choochooparts.com/body_g3.asp?CAT3=79120&CAT2=79000&CAT1=70000

Now we are talking.

 

[panteliss]

I like the prices on the fleabay i didnt know that husqvarna produce special edition tools made from titanium i must order some

 

[DSS]

Thanks man. Needle nose pliers have been my go to.

The only one of those I have is homemade. I been using needle nose too

 

[dall]

i will build any i will need i have some 1/8 inch stainless

 

[drf256]

that looks like a new cylinder al

New AM jug. I'm not taking my maiden voyage with something of value.

Sweet! What did you get?


Sent from my iPhone using Tapatalk

I believe OMTM, good quality Chinese lathe with milling attachment. I'm pretty happy with it and it sure beats the old Craftsman/Atlas 618 I had been using.