What's on your bench?

[heimannm]

Needs a bit of clean up before I put it in the display.



Mark

 

[Woodslasher]

My brother dragged this home, it runs fine but I need to tune it, sharpen the chain, and mebbe swap a roller nose bar onto it.

 

[Maintenance Chief]

My brother dragged this home, it runs fine but I need to tune it, sharpen the chain, and mebbe swap a roller nose bar onto it.
View attachment 390204

Get a picture of the outside spike , if its possible.

 

[Czed]

I have to fix that 011 I fixed 15 year's ago for my friend he never even ran it so it's set for 15 year's
He's 80 now and wants it running.
I got a free 55 just needs recoil and clutch cover.
Helped with a couple of 1968? 4hp Johnson and Evinrude's same engine
These belong to a literal multi millionaire that's too cheap to buy anything.

Trash starting assembly's they keep breaking
I told him to drill a hole in the top cover
and keep a cordless impact while fishing.
Parts are very expensive for these obsolete engine's.
I told him to buy one of these weed eater powered one
https://www.ebay.com/itm/394844276355
He won't though.

 

[Duce]

View attachment 390213
I have to fix that 011 I fixed 15 year's ago for my friend he never even ran it so it's set for 15 year's
He's 80 now and wants it running.
I got a free 55 just needs recoil and clutch cover.
Helped with a couple of 1968? 4hp Johnson and Evinrude's same engine
These belong to a literal multi millionaire that's too cheap to buy anything.
View attachment 390238View attachment 390239
Trash starting assembly's they keep breaking
I told him to drill a hole in the top cover
and keep a cordless impact while fishing.
Parts are very expensive for these obsolete engine's.
I told him to buy one of these weed eater powered one
https://www.ebay.com/itm/394844276355
He won't though.

That’s why he is worth millions. Good friend is self made millionaire and drives a rusty Ram pickup.

 

[Czed]

That’s why he is worth millions. Good friend is self made millionaire and drives a rusty Ram pickup.

Dodge owner's have to be excellent mechanics

 

[Matt Ellerbee]

FS94 with a bad vibration while running. Found the problem. Was also sorta shocked to see the bearing. Anyone know the SKF/NSK equivalent? 9503 003 5190

 

[gurwald]

If you have the ID, OD and width its easy.

https://www.skf.com/binary/tcm:12-121486/SKF%20rolling%20bearings%20catalogue_tcm_12-121486.pdf

 

[Maintenance Chief]

View attachment 390213
I have to fix that 011 I fixed 15 year's ago for my friend he never even ran it so it's set for 15 year's
He's 80 now and wants it running.
I got a free 55 just needs recoil and clutch cover.
Helped with a couple of 1968? 4hp Johnson and Evinrude's same engine
These belong to a literal multi millionaire that's too cheap to buy anything.
View attachment 390238View attachment 390239
Trash starting assembly's they keep breaking
I told him to drill a hole in the top cover
and keep a cordless impact while fishing.
Parts are very expensive for these obsolete engine's.
I told him to buy one of these weed eater powered one
https://www.ebay.com/itm/394844276355
He won't though.

Might be too much motor for him!

 

[nbbt]

The test run of the rebuilt Solo didn't go entirely as planned, The carb is getting a rebuild soon, and I'm looking at other items that might cause a fuel leak issue when turned on the PTO side.

And the oil pump is still leaking when not being used.

 

[slackinoff]

Husqvarna 575. My friend dropped off two that have been sitting in a dirt floor barn for close to 10 years. Unbelievably filthy. I got one just about finished….waiting on a carb kit. Which I already ordered but can’t find grrrr!

 

[old 040]

Needs a bit of clean up before I put it in the display.

View attachment 389973

Mark

I've been trying to buy one of these that's listed locally, seller hasn't even seen my sent messages, gets frustrating. Never know, may have had some kind of issue to not be able to respond, but if not, why do certain people list things and not check to see if someone has interest?

 

[farminkarman]

3120xp cylinder machine work:

 

[Moparmyway]

Are you chamfering the flywheel ?

 

[heimannm]

Mark

 

[heimannm]

Too many issues to make it a runner, I will find a place for it in the display.



Mark

 

[Woodslasher]

Get a picture of the outside spike , if its possible.

Book's upside down, picture's right side up.

 

[farminkarman]

Are you chamfering the flywheel ?

I will if I need to. I haven't looked that far ahead yet

 

[Mastermind]

I will if I need to. I haven't looked that far ahead yet

Sometimes you do, sometimes you don't.

 

[Maintenance Chief]

Book's upside down, picture's right side up.
View attachment 390516View attachment 390517

Thanks !, thats one heck of a big saw your brother got there.
Is it a runner?