What's on your bench?

[MustangMike]

That filter on the 10mm 044 looks like a "winter filter" with very course screen.

That said, if a 10mm 044 ran till now w/o blowing up, someone got their money's worth out of it!

Mine still runs good, but does not owe me anything!

 

[Sawcrazy]

Put the b&c on this new turd.
The 20mcs in the tote below is next on the chopping block….

 

[rogue60]

Here's for anyone who says air filters are unnecessary and that fines don't hurt a saw. Very early 10mm 044:
View attachment 333843
View attachment 333844 View attachment 333845 View attachment 333846 View attachment 333847

They could have got another couple thousand hrs out that saw if they didn't use chit oil lol

 

[Kiwioilboiler]

They could have got another couple thousand hrs out that saw if they didn't use chit oil lol

I wondered if your "spidey fines senses" would pick that one up.

 

[rogue60]

Gave my brother a hand putting a 4.2 1HD-FTE in one of his LandCruisers. Him and his wife do a lot of travelling around Australia.
Bloody Toyota's holding there value he paid 12k for the engine.



The old turbo 4.2 1HZ out of it still a good motor he'll get 4k for it.

 

[Kiwioilboiler]

Gave my brother a hand putting a 4.2 1HD-FTE in one of his LandCruisers. Him and his wife do a lot of travelling around Australia.
Bloody Toyota's holding there value he paid 12k for the engine.
View attachment 333900


The old turbo 4.2 1HZ out of it still a good motor he'll get 4k for it.
View attachment 333901

78 Series Troopy?

 

[rogue60]

Yeah I think he likes his Toyota's this is just some of em.

 

[rogue60]

78 Series Troopy?

Yeah his old Troopy

 

[RI Chevy]

How many miles/kilometers did he get out of the old motor that was replaced?

 

[slackinoff]

You work in a converted chicken coop?

lol. The previous owner of this house loved ski boats. It’s a tall two bay, three sided shop. I’d like to enclose it one day.

 

[merc_man]

Ms 260 i picked up other day on trade. Piston has some light scoring. Gonna pull it apart and see if it will clean up.

Sent from my SM-G950W using Tapatalk

 

[huskyboy]

Some helicoil action.

 

[Maintenance Chief]

Ms 260 i picked up other day on trade. Piston has some light scoring. Gonna pull it apart and see if it will clean up.

Sent from my SM-G950W using Tapatalk

Isn't that a Super because of the decomp?

 

[huskihl]

Isn't that a Super because of the decomp?

026 Pros and all MS260’s had decomps. Regular 026 didn’t

 

[merc_man]

026 Pros and all MS260’s had decomps. Regular 026 didn’t

Are the 026 pros and ms 260 pretty much same saw just plastic a bit different?
Same cylinders?
Port timing?

Sent from my SM-G950W using Tapatalk

 

[huskihl]

Are the 026 pros and ms 260 pretty much same saw just plastic a bit different?
Same cylinders?
Port timing?

Sent from my SM-G950W using Tapatalk

All the MS saws except for the 660 went to flippy caps. Right around then they started having a little bit more bubble look to the plastics. Early 260s had the same smaller 026 bore, but soon after they went to larger cylinder to get over 50cc to get around EPA regulations

 

[WillG]

Husqvarna 224L straight shaft 4 stroke trimmer. Based off a Honda GX25. New carb, fuel lines, fuel filter, plug and oil changed a couple times to get the contaminated oil out of the crankcase (was diluted with fuel from the faulty carb)

Sent from my E6910 using Tapatalk

 

[rogue60]

How many miles/kilometers did he get out of the old motor that was replaced?

The old engine has 480k (kilometres) on it doesn't burn any oil plenty of life left in it.
Down here we change oil at 5k. Nobody sends oil off for oil analysis don't even know if that con exists down here. just change the oil it's not hard 15-20k miles between oil changes yeah no thanks lol

 

[RI Chevy]

Wow. Nice. 480k and still going.

 

[RI Chevy]

Are the 026 pros and ms 260 pretty much same saw just plastic a bit different?
Same cylinders?
Port timing?

026 were 44mm
Newer 260 were 44.7mm