What's on your bench?

[a. palmer jr.]

I have on my bench an 028 Stihl with no bar oil to the chain. I took it apart and noticed all the gears worn out and the pump cover with a big hole in it where the gear is. I'm sure there's also a rubber oil hose somewhere on this saw but maybe it's in the tank rather than on the outside where I can see it. Now I have to figure out if it's worth it to buy all the gears and fix it..

 

[Glock37]

Started breaking down a long term resto project for the man cave (well my whole place is a man cave, 150+ chainsaw bars on living room floor while shed having new benches etc put in.).

She is a wee bit dirty.

View attachment 27532
View attachment 27533
View attachment 27534
View attachment 27535

Number ontop on cylinder seems to indicate it's the 110cc version, but will wait till I clean it up better to pull cylinder.

Contemplating a powder coat, but not sure..

The twin we did for brad



Sent from my iPhone using Tapatalk

 

[Redfin]

How did this one end up Mike?

 

[Glock37]

I dont think he started rebuild yet too busy

Sorta like yours 2100 !!!


Sent from my iPhone using Tapatalk

 

[Redfin]

Sorta like yours 2100 !!!

 

[Iron.and.bark]

The twin we did for brad



Sent from my iPhone using Tapatalk

Nice work.

Though I do think the chain cover/guard looks better in 2 tone not single :/

 

[Glock37]

How far along are ya. I got everything for the 395 just have to get 3 done before it


Sent from my iPhone using Tapatalk

 

[Glock37]

Nice work.

Though I do think the chain cover/guard looks better in 2 tone not single :/

Brad was going to do the black on chain cover


Sent from my iPad using Tapatalk

 

[Chainsaw Jim]

Fun fun fun. Rebuilding an 056av top end, oil gear and pump. I had to pull a flywheel and coil off another carcass just to get the damn wire grommet.


Up next......

 

[paragonbuilder]

Fs 55 burst its primer bulb. Pulled the screen on the muffler and dropped a new China carb on it for $7. Tuned and it runs better than it has in years.


Sent from my iPhone using Tapatalk

 

[Mastermind]

I have on my bench an 028 Stihl with no bar oil to the chain. I took it apart and noticed all the gears worn out and the pump cover with a big hole in it where the gear is. I'm sure there's also a rubber oil hose somewhere on this saw but maybe it's in the tank rather than on the outside where I can see it. Now I have to figure out if it's worth it to buy all the gears and fix it..

Check eBay for parts,

 

[USMC615]

Does a huge clusterphuck and gaggle of hand tools, to the tune of dozens, that need to find their way back to the roll-away tool box, constitute a 'what's on your bench' post?...Or does it fall into the 'get off my lazy ass and get'em put back where they belong' thread? Lol.

I do have an MS-211 that idles/runs fine, oils fine...but when sitting not running, over any length of time, seems to wanna belch and leak outta the bottom, every drop of bar oil in the tank. Gotta keep a plastic trash bag or two under the thing while it sits in a cardboard flat. I guess he needs a little surgery...

 

[paragonbuilder]

45 cc.

How the hell is that supposed to breathe. We can fix that!


Sent from my iPhone using Tapatalk

 

[paragonbuilder]

Damn little thing sounds pretty good and has excellent throttle response now. Still a little turd though...

Sent from my iPhone using Tapatalk

 

[Time's Standing Stihl]

^^45cc piss reving at its finest

Sent from my SM-G900R4 using Tapatalk

 

[DSS]

^^45cc piss reving at its finest

Sent from my SM-G900R4 using Tapatalk

Plus bonus points for extra curricular blipping [emoji106] [emoji106] [emoji202]

 

[paragonbuilder]

Lmao!


Sent from my iPhone using Tapatalk

 

[VinceGU05]

Had a little poo in the pants moment yesterday while test and tuning a recently finished off 084.
While giving a good piss rev like above, it suddenly back fired , sparks out of the muffler and stopped suddenly.
I slowly pulled it over with decomp on and felt OK. So I tried starting it. Not happy at all and ran for a second or two before quitting.
Ok muffler off and look for damage. None [emoji15][emoji848] pulled over fine. Can't be bearings.
Something said check the keyway[emoji72]
Sure enough sheared the keyway off and had about 25 deg advance [emoji13]
Cheap easy fix but worried that 20 thou off the keyway broke so soon. Maybe flywheel wasn't tight enough[emoji848]

 

[Stump Shot]

Had a little poo in the pants moment yesterday while test and tuning a recently finished off 084.
While giving a good piss rev like above, it suddenly back fired , sparks out of the muffler and stopped suddenly.
I slowly pulled it over with decomp on and felt OK. So I tried starting it. Not happy at all and ran for a second or two before quitting.
Ok muffler off and look for damage. None [emoji15][emoji848] pulled over fine. Can't be bearings.
Something said check the keyway[emoji72]
Sure enough sheared the keyway off and had about 25 deg advance [emoji13]
Cheap easy fix but worried that 20 thou off the keyway broke so soon. Maybe flywheel wasn't tight enough[emoji848]

...but are your pants still OK?

 

[heimannm]

Please keep you pants on for these photos, and feast your eyes!!!











Mark