What's on your bench?

[lehman live edge slab]

I got this saw and a 49sp both were low hour saws that were getting thrown out at a fire hall up here after sitting on a shelf for the last 15-20 years. The 49 is missing the wrap handle so I’ll need to find one after I get it running. This 52e runs great after complete fuel system clean with carb kit snd fuel line/filter.

 

[WillG]

Yes it was. They should all have a knock out or screwed on access plate in the back. I just had to cut the spot welds, mount the heat switch for the fan and mount the fan and plug it into an extension cord.

Sent from my E6910 using Tapatalk

 

[WillG]

Got a bunch of cleanup done before dinner. Gonna do the bench, tool box and lift table tomorrow evening. I'm in a pizza coma now....

Sent from my E6910 using Tapatalk

 

[tickbitintn]

Got this 51 sorted out.
Fuel system clean and rebuild.
Ran kinda funny and didn't want to tune out.
Dumb ass that went through the carb (me) forgot a gasket! Lol
Runs much better with gasket installed, don't know how I missed that...
Drop it in some wood tomorrow for a test run.
Probably see if I can find it a new home if all is well.

Sent from my XT1635-01 using Tapatalk

 

[WillG]

Making good progress on cleanup. The parts washer area will be tomorrow evenings project.

Sent from my E6910 using Tapatalk

 

[merc_man]

Getting my 066 ready. Put new fuel line, filter, and impulse line on it. Flushed the fuel tank a few time and got a lot of saw dust out. Hope it is good to go now.

With this style filter should i have a foam filter over top?

Sent from my SM-G950W using Tapatalk

 

[huskihl]

Getting my 066 ready. Put new fuel line, filter, and impulse line on it. Flushed the fuel tank a few time and got a lot of saw dust out. Hope it is good to go now.

With this style filter should i have a foam filter over top?

Sent from my SM-G950W using Tapatalk

Doesn’t need foam, but it should be oiled

 

[merc_man]

Doesn’t need foam, but it should be oiled

How do you oil that type? Is ther a spray oil?

Sent from my SM-G950W using Tapatalk

 

[lehman live edge slab]

How do you oil that type? Is ther a spray oil?

Sent from my SM-G950W using Tapatalk

K snd n and other companies make spray cans of oil for air filters

 

[merc_man]

K snd n and other companies make spray cans of oil for air filters

Thanks. Will look to see what I can find befor i get it out.

Sent from my SM-G950W using Tapatalk

 

[Duce]

Box-o-saw, two reduced to one. Only using oem parts except Caber rings and oregon fuel filter. Off topic, found this at feeding station.

 

[merc_man]

That came out of the fuel tank on my boys 026. No wonder it had running isues before we did the carb. And good thing for screens in funnles.

Sent from my SM-G950W using Tapatalk

 

[WillG]

Got started on the parts washer area. This corner is pretty messy so it's going to take a few evenings to get straightened up. Taking my waste oil to work Saturday to dispose of it in our 275 gallon waste oil tank.

Sent from my E6910 using Tapatalk

 

[tickbitintn]

Too much work today, no daylight left to get the 51 in some wood.
Probably gonna be a bit since we are supposed to get up to 7" of rain here between tomorrow and Tues....

Sent from my XT1635-01 using Tapatalk

 

[Cooper264]

Getting my 066 ready. Put new fuel line, filter, and impulse line on it. Flushed the fuel tank a few time and got a lot of saw dust out. Hope it is good to go now.

With this style filter should i have a foam filter over top?

Sent from my SM-G950W using Tapatalk

Is it just me or does that big gurl have a fancy red light on the side?

 

[lehman live edge slab]

Is it just me or does that big gurl have a fancy red light on the side?

If it does it’s a combination of many saws has a round top on it and only flat tops can be red lights.

 

[tickbitintn]

Break in the weather this afternoon gave me a chance to run a few saws and get a little cleanup done at the neighbors.
Saws all good to go. Not too bad of a day.


Sent from my XT1635-01 using Tapatalk

 

[Agent Smith]

Started fitting up a 346 top end on my 350. Got the machining done tonight

 

[WillG]

Corner is almost done! Planning on finishing up Sunday morning. Just need a case of 30 weight and I'll be all stocked on oil for a while. Recycling my used oil tomorrow. In addition to stocking up on oil I need to get some 1/4" fuel hose, clamps and Speedy Dry oil absorber.

Started on my buddy's Ariens 5520. Replaced the recoil rope and got the carb pulled and blown out with brake cleaner and compressed air. Planning on reassembly tomorrow afternoon. New fuel line installed as well.

Sent from my E6910 using Tapatalk

 

[lehman live edge slab]

the saws just keep finding me this last week or so. Guy at work brought me a 61 rancher and a 49sp jonsred. Few days ago I got a 49sp and 52e from a different guy at work that saved them from the scrap pile. Also got a real nice 036pro that will need a new piston