What's on your bench?

[Mastermind]

I have not been in any of those, they didn't sell much around here, but looks just like it's smaller sibling.

Sent from my XT1635-01 using Tapatalk

I've done a metric chit ton of these things. They finally got the bugs out.

 

[tickbitintn]

I've done a metric chit ton of these things. They finally got the bugs out.

I've always kinda wanted one (but have no use for one) and was hoping my local shop would get one in and abandoned.....
They have never had one come in, not even for service!

Sent from my XT1635-01 using Tapatalk

 

[Mastermind]

I've always kinda wanted one (but have no use for one) and was hoping my local shop would get one in and abandoned.....
They have never had one come in, not even for service!

Sent from my XT1635-01 using Tapatalk

I gave Shaun 3 carcasses at the gtg. He might have one to spare....

 

[Mastermind]

Twins !!!!

 

[tickbitintn]

I gave Shaun 3 carcasses at the gtg. He might have one to spare....

I need another saw like I need another hole in my head!! Lol

Sent from my XT1635-01 using Tapatalk

 

[tickbitintn]

Twins !!!!

View attachment 204040

Of course there was two sets of parts!!
Looking good. [emoji846]

Sent from my XT1635-01 using Tapatalk

 

[MG porting]

Twins !!!!

View attachment 204040

Even though I love Stihl but those huskys sure eye caching.

 

[Czed]

02 silverado these damn trans cooler line's
Are a pain to change
C clips with a rubber grommet are all that secure them.
And getting them routed was hell
Got two in the third i need my friends lift.

 

[MustangMike]

The new saws from both Husky and Stihl have to be a welcome accomplishment to dealers, porters, and users. I hear mostly all good news re new generation : 550, 562 and 572.

Rumer has it the MS 400 will be available soon … with less weight and more ccs than the 562, it will be interesting to see how it stacks up. 562s (especially ported) are very strong for their size.

 

[justoldsaws]

MS390 , new piston, rings, seals and bearings, waiting for the 3 bond to cure then back together.

 

[justoldsaws]

Ms390 all back together, fuelled and got to fire on a prime, then fuel pissed everywhere, found it had a cheap chinese fueline that had 3 splits in it.
A genuine line wont let me down.

 

[Mastermind]

Ms390 all back together, fuelled and got to fire on a prime, then fuel pissed everywhere, found it had a cheap chinese fueline that had 3 splits in it.
A genuine line wont let me down.
View attachment 204178 View attachment 204179

Note to self.....

Never use a Chinese rubber.

 

[redlight066]

Yahtzee!!

View attachment 204018

 

[PA Dan]

Twins !!!!

View attachment 204040

Put them up for adoption...[emoji13]

 

[MustangMike]

Quality control is ALWAYS an issue with Asian parts (all of them), but the only rubber I've found it necessary to replace with OEM are some of the AV rubber.

 

[gurwald]

Found a HD filter intake elbow so I converted to a hi-top, looks moor better and I wasnt impressed with the low top filtration.
Too purdy to mod I could never grind on this cylinder... But I got a AM muffler i gutted, thats all. Maybe advance timing also..

 

[huskyboy]

Found a HD filter intake elbow so I converted to a hi-top, looks moor better and I wasnt impressed with the low top filtration.
Too purdy to mod I could never grind on this cylinder... But I got a AM muffler i gutted, thats all. Maybe advance timing also.. View attachment 204218

They have huge squish, ditch the gasket in the least ... and .020 off the flywheel key.

 

[Stump Shot]

Let this swirl around y'all's brains a time or two and see if it goes pop!
6202

 

[PA Dan]

Let this swirl around y'all's brains a time or two and see if it goes pop!
6202
View attachment 204361

Hmmm....

 

[PA Dan]

Let this swirl around y'all's brains a time or two and see if it goes pop!
6202
View attachment 204361

So I'm curious to see what name is in the bearing itself.