What oil is best? and what ratio?

[X 66 stang347 X]

What mix?

Klotz kl200 and some super techniplate. I know people have stuck some rings running the super I've ran it for years. It doesn't get that cold here and it was about 75° at the time I was running it.

 

[Keith Gandy]

Klotz kl200 and some super techniplate. I know people have stuck some rings running the super I've ran it for years. It doesn't get that cold here and it was about 75° at the time I was running it.

U must be really rich for either Klotz not to combust and make alil carbon?

 

[junkman]

Im sure its been covered but can one of you remind me if kl200 stores well ? ... stabilizer ?

Mix it with saber 50-50















Klamsoil

 

[X 66 stang347 X]

That's on my old l77 I have been testing It doesn't turn many rpm's.
I pulled it back down to install the bearing that I was waiting on.

 

[concretegrazer]

Finally got around to fixing the transfer seals on the 550. & thought y'all might enjoy another crappy oil pic.

 

[porsche965]

What oil/ratio?

 

[Keith Gandy]

Finally got around to fixing the transfer seals on the 550. & thought y'all might enjoy another crappy oil pic.

View attachment 45938

Good bit of carbon on thoso rings it appears to be

 

[concretegrazer]

Lucas 32:1 primarily. Had some husky xp oil @ 50:1 run though it as well.

 

[concretegrazer]

Good bit of carbon on thoso rings it appears to be

The ring is fine.

 

[Keith Gandy]

The ring is fine.

Not tryin to be rude but Ill disagree. That carbon keeps building on that ring u will have problems sooner or later

 

[jake wells]

supertech boat oil at 10:1
i use 87 corn gas too it burns the bestest.

 

[jake wells]

running echo powerblend at 32:1 at the moment

 

[jake wells]

IMO its like RA, too much oil at 32:1

echo powerblend at 32:1 is a nice combination.

 

[concretegrazer]

Not tryin to be rude but Ill disagree. That carbon keeps building on that ring u will have problems sooner or later

No worries. Should be much better without those 2 big air leaks. Thank you husqvarna.

 

[Keith Gandy]

No worries. Should be much better without those 2 big air leaks. Thank you husqvarna.

That was on a 550? I had a flywheel side seal leak on a new 550

 

[jake wells]

That was on a 550? I had a flywheel side seal leak on a new 550

should have won a echo it wouldn't of leaked.

 

[concretegrazer]

should have won a echo it wouldn't of leaked.

But he'd have a thousand cuts by now from all that cheap plastic.

That was on a 550? I had a flywheel side seal leak on a new 550

Ya a 550.

 

[jake wells]

But he'd have a thousand cuts by now from all that cheap plastic.



Ya a 550.

pfftt.

 

[jk14]

HL supply has saber qt.$12, 8oz.$5,
3.5oz. $3 that's all I run @40:1

 

[skidooguy]

I ran saber for close to 8 years or better at 40-50 to 1 and only reason I got away from it was the fact I couldn't get it locally. Once I burn up this red armor I'll decide which oil I'll run. I also have a bunch of cheap oil I got from a hardware store going out of business but I'm thinking about only running the cheap stuff in my ms230 just to do a comparison to the expensive stuff. Mufflers in all my saws were clean with no spooge running saber. On the same note my 038 ran on 50:1 Stihl orange bottle all its life and never missed a beat.