The Swap Meet Thread

[Majorpayne]

Need a 503-2210-02 10mm x 1.00 x 14mm hex flywheel nut for an older Model 61 Rancher. Evidently NLA according to my dealer even though that size was used on lots of 1xx and 2xx saws of the day. 503-2210-03 is what's now available through the dealer but is a 17mm hex head and is too large for the recoil cup to fit down over it to engage the pawls, let alone allow the recoil assembly to fit properly.

They're out there for a couple bucks plus $10.00 shipping. Uh, huh. I'll take five...

TIA if anyone can hook me up.

Would a different recoil work with the larger nut?

 

[Mastermind]

Need a 503-2210-02 10mm x 1.00 x 14mm hex flywheel nut for an older Model 61 Rancher. Evidently NLA according to my dealer even though that size was used on lots of 1xx and 2xx saws of the day. 503-2210-03 is what's now available through the dealer but is a 17mm hex head and is too large for the recoil cup to fit down over it to engage the pawls, let alone allow the recoil assembly to fit properly.

They're out there for a couple bucks plus $10.00 shipping. Uh, huh. I'll take five...

TIA if anyone can hook me up.

I've got a 266 here.......will that nut work?

 

[PogoInTheWoods]

Yep.

 

[Mastermind]

I gotta ship some jugs tomorrow. PM me an address.

 

[PogoInTheWoods]

Would a different recoil work with the larger nut?

Been too busy scrounging for the nut to research the recoil assembly variants, but I'm sure there's a pulley with a slightly larger cup to accommodate the larger nut.

 

[PogoInTheWoods]

I gotta ship some jugs tomorrow. PM me an address.

Thanks, Randy. PM inbound.

 

[Wagnerwerks]

I'm back on the hunt for a OEM 346 closed port jug set. I have a couple top ends I could trade and tons of husky, pioneer, stihl 029-39 parts and more.

I could also use a pto case half.

Not really looking to buy . Just trade. I'm in no hurry

 

[jacob j.]

I'm back on the hunt for a OEM 346 closed port jug set. I have a couple top ends I could trade and tons of husky, pioneer, stihl 029-39 parts and more.

I could also use a pto case half.

Not really looking to buy . Just trade. I'm in no hurry

OE or NE?

 

[countryhog]

Need a 503-2210-02 10mm x 1.00 x 14mm hex flywheel nut for an older Model 61 Rancher. Evidently NLA according to my dealer even though that size was used on lots of 1xx and 2xx saws of the day. 503-2210-03 is what's now available through the dealer but is a 17mm hex head and is too large for the recoil cup to fit down over it to engage the pawls, let alone allow the recoil assembly to fit properly.

They're out there for a couple bucks plus $10.00 shipping. Uh, huh. I'll take five...

TIA if anyone can hook me up.

You could take a grinder to the new nut

 

[Wagnerwerks]

OE or NE?

Rather be. I'd take a 350 CP or 353 top too. I have an open port top here.

 

[paragonbuilder]

I'm looking for a 394 clutch side cover. Doesn't need to be pretty. My clutch has just about spun through the cover.


Sent from my iPhone using Tapatalk

 

[jacob j.]

Rather be. I'd take a 350 CP or 353 top too. I have an open port top here.

What I meant was- "Old Edition" 42mm bore, or "New Edition" 44.3mm bore, which would be your preference? I might have a decent OE jug here somewhere. The NE top ends new from Spike60 are $105.00.

 

[Wagnerwerks]

Are the oe closed port? I'll have to read a little more. I'm not up on my little huskies enough.

 

[psuiewalsh]

Yes. Smaller bore 45cc?

Sent from my XT1585 using Tapatalk

 

[Stump Shot]

Still have this cylinder I posted on the scores thread. It's just as it came to me, never used, I believe it's for a 066, has a 54mm bore. No ID on it, some type of aftermarket and closed ported. Piston included, however there are no rings, pin, clips or bearing. Same deal though, anyone that would like to use it, I'll send it your way.

 

[Redfin]

Looking for a long 44"+ 3003 bar. Not picky on pitch or gauge.

 

[Stump Shot]

Still have this cylinder I posted on the scores thread. It's just as it came to me, never used, I believe it's for a 066, has a 54mm bore. No ID on it, some type of aftermarket and closed ported. Piston included, however there are no rings, pin, clips or bearing. Same deal though, anyone that would like to use it, I'll send it your way.

@Mastermind I thought surely someone would scarf this up. Could I send it to you? Unless you maybe know of somebody I could send it to? I'd really like to "pay it forward" as I will probably never come into the need of it. Really do not want anything for it, I'll even pay to ship.

 

[Mastermind]

@Mastermind I thought surely someone would scarf this up. Could I send it to you? Unless you maybe know of somebody I could send it to? I'd really like to "pay it forward" as I will probably never come into the need of it. Really do not want anything for it, I'll even pay to ship.

Honestly, I'll never use it. I pitch most aftermarket jugs in the trash and replace them with OEM. There are some good ones out now, but they have some id makings on them.

 

[Stump Shot]

Honestly, I'll never use it. I pitch most aftermarket jugs in the trash and replace them with OEM. There are some good ones out now, but they have some id makings on them.

Guess I'll put it in a box with the rest of my curiosity's.

 

[Mastermind]