So what did you do today?

[Wilhelm]

Been browsing OPE on and off all morning.
Just had my second coffee.

I am vaguely trying to force myself to go outside, but the extreme cold wind gusts are making it way to easy to resist the urge.

All my work chains are dull (one loop per saw), I should try and get at least some of them back to proper working condition.
We'll see how the remainder of the day folds out.

 

[Viper21]

One load cut, a third of the way thru it.
My 281xp is out of action with a busted chain tensioner, so the 3120 had a run.View attachment 167080 View attachment 167082 View attachment 167083

That condom is too small for your 3120

 

[merc_man]

Been browsing OPE on and off all morning.
Just had my second coffee.

I am vaguely trying to force myself to go outside, but the extreme cold wind gusts are making it way to easy to resist the urge.

All my work chains are dull (one loop per saw), I should try and get at least some of them back to proper working condition.
We'll see how the remainder of the day folds out.

Were supposed to get some high winds later today and into tomorrow. Better have a walk around and make sure all my crap is picked up. Last time i had to go for a walk to find my one tarp.

Sent from my SM-G950W using Tapatalk

 

[USMC615]

Same ol' C-17/flightline song and dance today!

 

[Wilhelm]

I did some maintenance on 4 of my saws today, PS-550, PS-7310, PS-7300 & PS-7900.
Checked and cleaned AF's, cleaned the inner surface of the clutch drums, oiled the drums needle bearings, topped off fluids, sharpened chains and gave them a test run, a couple cookies each in my last 20ish" oak log.

I figured out the rails on my Ozaki bar got too low, both sides, drive links are bottoming out making the chain cut sideways - I kept thinking the chain was sharpened poorly.
Same issue on one of my Dolmar branded Oregon bars, just one side though.

Two things I need to do, muffler mod my PS-550 and remove the carb limiter's on my PS-7300.

 

[Dougbert]

Split some black oak by hand. Rearranged my diminishing firewood supply to get the seasoned stuff separated. Meeting my neighbor later to discuss some electrical issues with our shared water system. Ugh.

 

[merc_man]

Went to the boat shiw to do some dreaming. This is the brand new modle of what i have other then this has an evinrude on it.

Then baught an overpriced locked up tighter then bark to a tree chainsaw for 30 bucks. But always wanted one. Hope its locked up from sitting.

Sent from my SM-G950W using Tapatalk

 

[hoskvarna]

Went and played in the woods yesterday
Brother was felling and I was skidding.

Sent from Hoskey Hills

 

[Simondo]

2 stage take down of a sycamore from a multi stem tree.



Was a little tight for space to get in there to fell the butt section.



Took a few more overhanging limbs ....





Bit of a clear up ...

 

[Simondo]

Ps-7910..20"....Ps-420cs..15" ......Job done.

 

[fearofpavement]

View attachment 168087

Ps-7910..20"....Ps-420cs..15" ......Job done.

Be careful where you lay your chainsaw, we don't want any "oops" pics posted on here.

 

[fearofpavement]

Spent the better part of a day putting in a posthole. Yeah, one posthole. I now have a wheelbarrow half full or rocks with some nearly football size. The 3" diameter roots were no help either. I stopped about 6" shallower than I wanted because I hit a rock so large I couldn't find any edges. So that corner post is setting on the rock. now only 9 more to go...

 

[fearofpavement]

Oh, and just to add to the above, This was a large diameter corner post and when I was finally able to wrestle it into position and drop it into the hole, I was quite pleased with myself as it was too heavy for one person to handle. I was measuring the protruding portion to see if I was down far enough and in the process fumbled my tape measure. It of course found that crack between the post and the hole and went to the bottom. My arm was about 4" too short to reach it and I thought for a while as to whether that was going to be the final resting place for the tape measure. If it wasn't a good 25' Stanley, it would have remained. I finally got the post back out of the hole and extracted the tape with the post hole digger. It was just a great day all around!

 

[Simondo]

Be careful where you lay your chainsaw, we don't want any "oops" pics posted on here.

No fear...there was some "saw placement for effect" ...going on !

 

[justoldsaws]

Just got back from a mates sheep farm, was out there shooting foxes, managed to get 5, lambs are due to be born in another 4 weeks, trying to thin out the fox numbers.

 

[Dustin4185]

Got a little burning done yesterday. Was too tired to post last night.

 

[justoldsaws]

Just got back from a mates sheep farm, was out there shooting foxes, managed to get 5, lambs are due to be born in another 4 weeks, trying to thin out the fox numbers.

All scalped for the fox bounty we have in my state.

 

[Dub11]

All scalped for the fox bounty we have in my state.
View attachment 168165

How much does the bounty pay?

I'm surprised there ain't a market for the whole pelt. Last time I was at my local Cabelas they were wanting $100 for a skunk pelt.

 

[justoldsaws]

How much does the bounty pay?

I'm surprised there ain't a market for the whole pelt. Last time I was at my local Cabelas they were wanting $100 for a skunk pelt.

For each fox i get $10, the fox skin market died out many years back.
Each wild dog scalp is $150

 

[birdmeter]

well i took a *s-word this week.