Saw video thread

[CR500]

Pretty Pumped to finally have an 064 done by J.

Also will be nice to have the 7900 ported.... Been 2yrs but it will be nice to have that done as well

 

[Toad22t]

Pretty Pumped to finally have an 064 done by J.

Also will be nice to have the 7900 ported.... Been 2yrs but it will be nice to have that done as well

I just got my 7900 ported by Mike Lee and I just love it.

 

[Time's Standing Stihl]

It's definately stout. J has those 1122's figured out.

Sounded a fuzz lean? What rpm you at?

I heard what your taking about, at the end of the 2nd cut. Couldn't tell ya what rpm it was at that point in time. The day before at the Michigan gtg i had it fairly fat at 14.1-14.2 and never touched the carb.

All I can think is the phone made it sound a bit lean?? Next time I run it I'll put a tach on it and see where it's at.

I know when Jason had it he was having it 4 stroke at 15k

 

[Deets066]

I heard what your taking about, at the end of the 2nd cut. Couldn't tell ya what rpm it was at that point in time. The day before at the Michigan gtg i had it fairly fat at 14.1-14.2 and never touched the carb.

All I can think is the phone made it sound a bit lean?? Next time I run it I'll put a tach on it and see where it's at.

I know when Jason had it he was having it 4 stroke at 15k

Tune is somthing you really need to keep an eye on when you have a saw of that caliber. Few of my local buddy's want me to build em some sort of race saw but can't tune their saw from summer to winter and leave the gas in it for 6 to 8 months at a time.

 

[CR500]

Tune is somthing you really need to keep an eye on when you have a saw of that caliber. Few of my local buddy's want me to build em some sort of race saw but can't tune their saw from summer to winter and leave the gas in it for 6 to 8 months at a time.

Good ears Deets The first cut sounded good but you could hear that scream at the end of the second cut... It did not have that lubber noise

I usually just tach a saw when temp swings are drastic. I will be sure to check tune daily,

A simple check can save huge problems lol

 

[Deets066]

Good ears Deets The first cut sounded good but you could hear that scream at the end of the second cut... It did not have that lubber noise

I usually just tach a saw when temp swings are drastic. I will be sure to check tune daily,

A simple check can save huge problems lol

I'm constantly listening to the tune.

 

[Chainsaw Jim]

I got the carb tuned right today. The low was way too lean.
Here it is running the same exact set up before and after addition of the pipe.

 

[johnny5ny]

Woods port, tuned to 14.4k, holding 12.7k in the cut...20" seasoned hard maple.

sounds awesome!!!
very nicely done brother!

 

[XP_Slinger]

sounds awesome!!!
very nicely done brother!

Thanks man. Now I just gotta get into my 346NE

 

[hseII]

I got the carb tuned right today. The low was way too lean.
Here it is running the same exact set up before and after addition of the pipe.

Hot!!

 

[CR888]

Nice to see Jim got that pipe fitted nicely. A little difficult mating a round and a square shape, hope its doing what it should and exhaust flow is good.

 

[Chainsaw Jim]

Nice to see Jim got that pipe fitted nicely. A little difficult mating a round and a square shape, hope its doing what it should and exhaust flow is good.

I beveled the base plate and spacer so they have a nice taper for the round shape to match up with.
My next step for this build is to fit a larger carb and boot up to it. It is currently running a stock WJ39 carb.

 

[hseII]

I beveled the base plate and spacer so they have a nice taper for the round shape to match up with.
My next step for this build is to fit a larger carb and boot up to it. It is currently running a stock WJ39 carb.

Warner Brothers to the Wescue.

 

[Chainsaw Jim]

I'm assuming many have already seen this but I'm going to post it anyways because this is one of the most badass chainsaw competitions you'll ever see.

 

[Stump Shot]

I got the carb tuned right today. The low was way too lean.
Here it is running the same exact set up before and after addition of the pipe.

You would have been handy to have around when we were cutting deck posts the other day. ha-ha Nice job on the saw!

 

[Stump Shot]

Cool old McCulluch.

 

[Chainsaw Jim]

Cool old McCulluch.

For those who've heard of Walker or "Walkerized" saws, that is old man Walker himself in the background.

 

[hseII]

Billy Smith seems like a Good Dude.

There are a few of his videos with Mr. Walker.

 

[burkesw]

Cool old McCulluch.

Buckin's channel is great, he's such a character. Would be a fun guy to be hang out with

 

[Deets066]

For those who've heard of Walker or "Walkerized" saws, that is old man Walker himself in the background.

I've ran a few walkerized saws, nothing impressive when you open them up. (Work saws) but run damn good in the wood