husqvarna 562,best ported saw ever?

[sawmikaze]

Everything has its place.

Ta-da

 

[Ktoom]

A few years ago, I owned a MMWS562p. I was very very impressed with the saw and it was go to saw at the time.... Only problem is I dropped a tree on it and sold it. Fast forward 3 years later, I'm began a quest in trying to find a 562xp builder as I liked my previous 562 so much. I found a builder back in the fall and just finished it a week ago. Now where should I send it????

 

[jmssaws]

I ran 2 of the fastest saws I've ever ran Saturday and the 562 wasn't one of them but it's the one that I was the most impressed with.

 

[R2D]

I have had a wicked ported 2253 for a while now. It's a great saw. But I'm thinking I'd rather have extra Cc's and extra couple bar inches in a ported 60cc saw at the cost of a extra lb. But that's me.

What is the rpm maxed out at on a 562? My 2253 sounds like it to maxes out at 20,000 lol!

 

[Chris Zautner]

I ran 2 of the fastest saws I've ever ran Saturday and the 562 wasn't one of them but it's the one that I was the most impressed with.

well what were the 2 saws lol

 

[hseII]

A few years ago, I owned a MMWS562p. I was very very impressed with the saw and it was go to saw at the time.... Only problem is I dropped a tree on it and sold it. Fast forward 3 years later, I'm began a quest in trying to find a 562xp builder as I liked my previous 562 so much. I found a builder back in the fall and just finished it a week ago. Now where should I send it????

I'm Bias, but keep it in the animal kingdom: either a Monkey or a Hog.

I suppose technically,
A Jackass is in the animal kingdom, but I don't care for Flying saws, so I'll stick with a sure Thing. [emoji41]

 

[hseII]

I ran 2 of the fastest saws I've ever ran Saturday and the 562 wasn't one of them but it's the one that I was the most impressed with.

What were they?

 

[jmssaws]

well what were the 2 saws lol

Hedgerow's 346 and his Treemonkey 064

 

[Chris Zautner]

Hedgerow's 346 and his Treemonkey 064

video of the 064?

 

[Chris Zautner]

this 064 is fast!!

 

[jmssaws]

video of the 064?

I don't post videos of saws that ain't mine plus I didn't get one.

 

[Workshop]

I've got 4 saws that I take with me to cut firewood with. (Used to be 15-20) Two 50cc running 18 and 20 inch bars, (MS260, Dolmar 111), a ported 67cc running a 24 inch (Echo 670)and a ported 88cc running a 28 inch,(390XP). But I would like to have a 60cc with a 20 inch for overall use. After looking, reading, talking and seeing different ones in this range. Saturday I was convinced that a 562XP, done by Allen, no one else, (no disrespect intended to other builders) would be my next saw. It will be a while, though. (I'm still paying off the 390).

 

[rburg]

I have run his 064 and it is very strong.

 

[jmssaws]

I have run his 064 and it is very strong.

Not many will run like that one

 

[awol]

Ain't that the saw you got pinched in a big ol red oak, and had ta get cut out by a Dolmar?!!!

 

[Hedgerow]

What were they?

Lol...


They were "perspective"..

It's valuable, even if it can be expensive at times..

 

[Crzybowhntr]

I have a good bottom end if you need it.

I can only imagine what this one liner will turn into...

 

[paragonbuilder]

I just grind the piston to make the strato timing match the intake timing, so that both the intake and strato ports begin to flow at the same time.

What is your thinking on this Allen? Not much talk of strato saw improvements here. Looks like you have a good handle on it.


Sent from my iPhone using Tapatalk

 

[Deets066]

Okay let's run it down.

MMWS 044 Check
DRF255 026 - Need
AWOL 562 - Need
JMSSAWS 066 - Need
TreeMonkey 661 - Need

I know there is more I'm missing but *s-worde it's way beyond requiring a simple bank heist at this point...

Mike Lee 7900

 

[Hedgerow]

Ain't that the saw you got pinched in a big ol red oak, and had ta get cut out by a Dolmar?!!!

Lol...

Hooray dolmar!!!

But then again, I can get pinched with anything..
So I can't talk.