how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Fishnuts2]

I know I'm not "all there" sometimes
And Lord knows i try to pay attention
(Who am I kidding my attention span is tiny) but I was working at annoying
My wife today. ...
Made a people LOL for real.... good times!
If I could only get paid to paid to be a spazz

You're still OK if she still goes to Walmart with you. I think I went past the limit for mine, and now she won't be in the same isle as me anymore

 

[Louie B]

Good morning to all

 

[67L36Driver]

Morning midlanders!

Happy holidays!

 

[stihl livin]

Mike I'm going to be needing one of them adapters to mount a stihl bar on a solo. I'll get with you next week when it's not so hectic with Christmas.

Morning to the southern folks now turn off the fans so we get snow instead of the rain tomorrow

 

[67L36Driver]

Not sure if mine is annoyed or embarrassed most of the time..


I think mortified mostly.

Just plain scared occasionally.

 

[Workshop]

Morning everybody.
New coil came in for the husky 41 yesterday. Got it installed along with a new plug. Test spin with a drill to check it. No spark. What the ©®¢%. Put the old one back on (it still works but the spade connector was broke off) still no spark. Grab an old plug and spin again. Spark!! Put the new coil back on, spark. Put the new plug in, no spark. I've read others have had this happen but I've never seen it, until now.
NGK plug, bought 5 of them. Others checked ok.

 

[Homelite410]

Good morning fellas!

 

[sawnami]

I know I'm not "all there" sometimes
And Lord knows i try to pay attention
(Who am I kidding my attention span is tiny) but I was working at annoying
My wife today. ...
Made a people LOL for real.... good times!
If I could only get paid to paid to be a spazz

So we're both in this club Cobey?

Sent from my SM-T900 using Tapatalk

 

[Time's Standing Stihl]

Morning gents

 

[Ethan Hamby]

Probably gonna buy a walbro carb for this saw... Pretty sure this one is pure junk

 

[67L36Driver]

Probably gonna buy a walbro carb for this saw... Pretty sure this one is pure junk

Check the metering lever spring and see if it is a shortish, squaty item or a honkin' long one.

My 361 wouldn't hardly run with the long one. Or, even start without a prime.

 

[Ethan Hamby]

Check the metering lever spring and see if it is a shortish, squaty item or a honkin' long one.

My 361 wouldn't hardly run with the long one. Or, even start without a prime.

mine will not stop pooling in the crankcase. And no matter how I set the low or the idle it does it

 

[Ethan Hamby]

It runs and idles fine. Throttle response is decent but even then it pools and I can't even turn the saw on its side

 

[Ethan Hamby]

Would that cause that?

 

[huskihl]

Check the metering lever spring and see if it is a shortish, squaty item or a honkin' long one.

My 361 wouldn't hardly run with the long one. Or, even start without a prime.

My Asian 361 has a split second rich bog off idle. I think this is where it's at. Heavy spring forces you to open the L screw so it will idle. But at 1/8 throttle, she's waaay too rich

 

[Ethan Hamby]

See unless I open the l up almost all the way it won't idle at all. No matter where I set the idle

 

[huskihl]

See unless I open the l up almost all the way it won't idle at all. No matter where I set the idle

Spring

 

[Ethan Hamby]

Damn... Guess I need to strip the carb off for a 4th time lol

 

[67L36Driver]

Spring

To the people (children?) that put the carb together, one spring fits all.[emoji847]

 

[cobey]

Merry Christmas eve day to all my good friends. .....