how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[Hedgerow]

View attachment 98901

Good gravy, I'm sore today. I think I'll take a day off from cutting wood tomorrow. Any volunteers to unload my truck in the morning?

I'm guessing it's the Hickory though.

Due to the moisture content and wood density, should be virtually identical. Though once dry, the hickory may get the nod.



As long as the bugs don't tip the scale in favor of the white oak.
Just sayin..

They love hickory..

 

[Locust Cutter]

Sounds very interesting.
What is your field of expertise?

SIGINT as a whole, while specializing in ELINT or Electronic Intelligence. For fear of saying too much, google will aptly describe the basics of my job.

 

[Locust Cutter]

The TS/SCI clearance is a bonus too.

 

[cobey]

Moved the spinner tool box,
I' getting a 36" wide stand up
Desk / cabinet tomorrow from
Work, I hope it makes a better
Work area

 

[67L36Driver]

I often think a large office desk with swivel chair would be a nice ‘geezer tinkers saws’ setup.[emoji848]

 

[plcnut]

SIGINT as a whole, while specializing in ELINT or Electronic Intelligence. For fear of saying too much, google will aptly describe the basics of my job.

Cool beans!

 

[plcnut]

Good morning all!

 

[Workshop]

Morning everybody.

 

[teacherman]

SIGINT as a whole, while specializing in ELINT or Electronic Intelligence. For fear of saying too much, google will aptly describe the basics of my job.

Basically your job is to keep the rest of us safe. Thank you.

 

[teacherman]

Howdy folks.

I have been weatherizing my front porch a bit, trying to run a new gas line throughout the basement, and finding leaks. Apparently 1" pipe is harder to tighten sufficiently, and it doesn't help that I recessed the main pipe between a beam and the furnace trunk line. Oh well. It will be a very good system when it's done. I did get the wood burner hooked up to the ductwork, and it does work, but I think the hot air will move better if I connect the shroud around the burner to the cold air return duct. That way I don't have to keep the basement door open for the air to move. Lot of work involved. Hope you guys are doing well. Nancy is still improving. Yesterday was the six year anniversary of her near-fatal attack by her former husband, so it was pretty stressful, but we went out for a good dinner and each day gets us a little further along from the tougher times.

Take care, be safe.

 

[67L36Driver]

Morning midlanders!

Lowering rakers on some chains so I can load the 066 clone.

I hate it.[emoji37]

 

[cobey]

Morning midlanders!

Lowering rakers on some chains so I can load the 066 clone.

I hate it.[emoji37]

Chain or the saw....

 

[cobey]

The new to me work table, I think some saws will fit in it too

 

[Dub11]

The new to me work table, I think some saws will fit in it too

Is that top slanted?

 

[Dub11]

I could send you a press blanket. There pretty tough and can give the work surface some grip.

 

[67L36Driver]

Dang it to hell!

Went to the trouble of dressing this bar to discover a tooth missing off the nose sprocket.

Just a laminated Stihl E but.......[emoji90]

 

[cobey]

I could seen you a press blanket. There pretty tough and can give the work surface some grip.

That would be cool, it' a little slanted
I figured I'd block the front up a couple inches

 

[Hedgerow]

Dang it to hell!

Went to the trouble of dressing this bar to discover a tooth missing off the nose sprocket.

Just a laminated Stihl E but.......[emoji90]

Just keep using it Carl..
It'll be ok.

 

[67L36Driver]

Just keep using it Carl..
It'll be ok.

I’ll throw it on something and try it out.[emoji848]

Farmertec 066 is ready for a new home.[emoji6]

 

[Dub11]

That would be cool, it' a little slanted
I figured I'd block the front up a couple inches

I'll see what I cam find. and what the dimensions of the top?