PAST CT GTG 2016 May 7th

[drf256]

I think my neighbors are assured that I do too now!

I bet they won't tell you though.....

 

[drf256]

Well Marcello and Al left before we got to that mount. However Eric dynoed his.

I'd like to know those results. We know where ours placed next to it in wood.

 

[drf256]

Kool videos fellas.
Them 262s look good

We came up with the numbers based upon the theories you and I have been talking about.

 

[paragonbuilder]

We came up with the numbers based upon the theories you and I have been talking about.

Just goes to show, rules are meant to be broken! And so we shall keep experimenting!!!

 

[juttree]

I had a chance to make a couple cuts with Marcello's mastermind 461 at his house and that's one hell of a strong saw. AND it's still set a bit rich.

 

[malk315]

I'd like to know those results. We know where ours placed next to it in wood.

The graphs from the runs of my MMWS 262 are some of the prettiest in terms of seeing visually a power curve. Least spikey. I think we got Bills stock 262 and his ported 359 for a sort of dyno 60cc comparisons. It will be tonight that I'll be able to get some data to share with owners. On the road now for mothers day duties.

Sent from my XT1080 using Tapatalk

 

[paragonbuilder]

The graphs from the runs of my MMWS 262 are some of the prettiest in terms of seeing visually a power curve. Least spikey. I think we got Bills stock 262 and his ported 359 for a sort of dyno 60cc comparisons. It will be tonight that I'll be able to get some data to share with owners. On the road now for mothers day duties.

Sent from my XT1080 using Tapatalk

And they deserve your attention Eric! You've put a lot into this, I'm sure you've sacrificed some time with them for all you've done. So thank you and your family for that! We can wait...

 

[Boozer]

I had a chance to make a couple cuts with Marcello's mastermind 461 at his house and that's one hell of a strong saw. AND it's still set a bit rich.

Fred had a big smile after he ran it late in the day. After it's fully broken in you can adjust it proper.
I am certainly not going to mess it up by doing anything on that carb. MM flat out builds a great saw.

The square ground loop Skippy (Chris) sent with the saw was GOOD. Matty gave me a tutorial on round
with Bill chipping in between dyno runs...getting there slowly. Mostly you'll be getting them!

 

[paragonbuilder]

I am really looking forward to seeing some dyno figures!

What I want to know is............. What the hell do you do with all the cookies?

From this

To this

To here

Even my boiler likes snacks!
They are a bit wet but they'll burn. And they dry fast in my 100 degree room!

 

[paragonbuilder]

So we never did tear down Wiggs saw... However with a stock muffler it turned into an absolute turd!


Sent from my iPhone using Tapatalk

 

[Boozer]

I can run the saw back up there Dan, just say the word. I thought you guys did the 262's on Friday.
Whatever needs to be done to advance the progress on these things is fine with me.

 

[malk315]

Thanks again to you and Yulyia for hosting. Also shout out to Mel and Cindy. It is awesome you can use the cookies. Very little waste. Also very much enjoyed food from Al, Marcello, and Fred and I hope didn't miss anyone who brought food! Thanks!

Sent from my XT1080 using Tapatalk

 

[paragonbuilder]

I can run the saw back up there Dan, just say the word. I thought you guys did the 262's on Friday.
Whatever needs to be done to advance the progress on these things is fine with me.

Thanks Marcello. I'm not sure when I can get together with both bill and eric again. If there is an opportunity I'll let you know.
We didn't because they are small mount 3/8, we just didn't get that far...

 

[paragonbuilder]

Thanks again to you and Yulia for hosting. Also shout out to Mel and Cindy. It is awesome you can use the cookies. Very little waste. Also very much enjoyed food from Al, Marcello, and Fred and I hope didn't miss anyone who brought food! Thanks!

Sent from my XT1080 using Tapatalk

Thanks Eric! I'm glad some of you were able to meet my wife Yulyia this year. She has been super supportive of my passion! Maybe next year she will be running saws....

 

[paragonbuilder]

I'm trying to keep the spirit going as I clean up

I'm not sure I will be able to ship this saw back though...


Sent from my iPhone using Tapatalk

 

[jmssaws]

I'm trying to keep the spirit going as I clean up

I'm not sure I will be able to ship this saw back though...


Sent from my iPhone using Tapatalk

Pull the cylinder on it,you will be surprised what's inside.

 

[jmssaws]

Unless my guage is off...

Sent from my iPhone using Tapatalk

I would have never guessed that the strongest saw I've ever ran would be 175lb of compression. My how things change! There's a lot that can be learned from this.

Transfer velocity is what makes power,timing can be here and there if you have velocity.

 

[Deets066]

I'm trying to keep the spirit going as I clean up

I'm not sure I will be able to ship this saw back though...


Sent from my iPhone using Tapatalk

I gotta get me some of them klotz candles

 

[paragonbuilder]

Pull the cylinder on it,you will be surprised what's inside.

Does it have a base gasket?

 

[jmssaws]

Does it have a base gasket?

Yes.
I don't use sealor.